• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Berg Build

OP
OP
Tcb3078

Tcb3078

Sr. Member
Joined
Jan 4, 2016
Messages
496
Loc.
Charlotte
Thanks

Gorgeous truck BTW !

Thanks.

I attached a dirty sketch with measurements.

Materials needed:
2x2 tubing
2x3 tuning
2x4 tubing
Grade 8 bolts
A to z fab mega spindle
Latch of choice
A to z fab tire mount
Stock bumper

Steps:
Measure and cut metal. Note the frame rail piece is the only 2x4. I did that so I could notch a support to the bottom bumper piece. Also, you will want to measure your tire width from center of wheel to outside of tire to get the correct length needed for the top piece. I didnt mark it in the picture, but I had 1.25 inches of space between the bottom 2 pieces to allow for the dumper to be slide in ask well as some bump stoos.

Weld. Make sure your notch for the spindle is level and square. Otherwise, you'll be swinging at an angle.

Paint, powder coat, or bedliner like I did.

Cut out hole in stock bumper for spindle

Assemble. As mentioned about, I put stock hood styoe bumpers on the bottom of the rail that swings as extra cushion. Place the latch where you want. Also, I haven't done it yet, but I'm plan on installing a limiting strap so that the bumper doesnt fly open. It will be a a strap for our doors.

Hope this helps
 

Attachments

  • 20190113_182151.jpg
    20190113_182151.jpg
    68.2 KB · Views: 141
OP
OP
Tcb3078

Tcb3078

Sr. Member
Joined
Jan 4, 2016
Messages
496
Loc.
Charlotte
Some more pics of the bumper
 

Attachments

  • 20190117_201841.jpg
    20190117_201841.jpg
    59 KB · Views: 136
  • 20190117_201832.jpg
    20190117_201832.jpg
    61.5 KB · Views: 149
OP
OP
Tcb3078

Tcb3078

Sr. Member
Joined
Jan 4, 2016
Messages
496
Loc.
Charlotte
Hit a huge milestone today. Pretty excited.

Also took some snaps of my wire routing in engine bay
 

Attachments

  • 20190208_203528.jpg
    20190208_203528.jpg
    92 KB · Views: 137
  • 20190208_232245.jpg
    20190208_232245.jpg
    93.9 KB · Views: 142
  • 20190208_232238.jpg
    20190208_232238.jpg
    107.2 KB · Views: 144
OP
OP
Tcb3078

Tcb3078

Sr. Member
Joined
Jan 4, 2016
Messages
496
Loc.
Charlotte
My view this afternoon coming things up
 

Attachments

  • received_545975249242459.jpg
    received_545975249242459.jpg
    79.7 KB · Views: 122
OP
OP
Tcb3078

Tcb3078

Sr. Member
Joined
Jan 4, 2016
Messages
496
Loc.
Charlotte
FINALLY installed the column and shaft. Had to make a custom mount under the dash due to the fiber tub. Maiden voyage it tomorrow... pending weather.
 

Attachments

  • 20190223_215452.jpg
    20190223_215452.jpg
    92.5 KB · Views: 167
  • 20190223_215250.jpg
    20190223_215250.jpg
    85 KB · Views: 177
  • 20190223_215304.jpg
    20190223_215304.jpg
    77.5 KB · Views: 211
OP
OP
Tcb3078

Tcb3078

Sr. Member
Joined
Jan 4, 2016
Messages
496
Loc.
Charlotte
She's alive and drives. No seat but like a dream
 

Attachments

  • 20190224_182654.jpg
    20190224_182654.jpg
    68.8 KB · Views: 140
  • 20190224_182704.jpg
    20190224_182704.jpg
    69.7 KB · Views: 153
  • 20190224_182731.jpg
    20190224_182731.jpg
    93.5 KB · Views: 170
OP
OP
Tcb3078

Tcb3078

Sr. Member
Joined
Jan 4, 2016
Messages
496
Loc.
Charlotte
Just an update. Been chasing little bugs around. But drove it for 14 miles yesterday, did a couple burnouts, and enjoyed it.. still no seats, but fun times

Also picked up another truck
 

Attachments

  • 20190316_142413.jpg
    20190316_142413.jpg
    94.4 KB · Views: 118
  • FB_IMG_1552430990050.jpg
    FB_IMG_1552430990050.jpg
    75.3 KB · Views: 139
  • 20190316_194042.jpg
    20190316_194042.jpg
    88.5 KB · Views: 131
Top