What have you done to your Bronco today?

dsenatore · Jun 23, 2018

Indeed. Having done the full driveway restoration over 23 years ago it's slowly coming back to me, cussing included! The list was a lot shorter and lighter when I brainstormed what I "thought" it needed to get rolling again.

Oh well... I certainly appreciate everyone's support that's chimed in! Back to it.

Montoya · Jun 23, 2018

Both brake lines on front axle now. Rear next.

sprdv1 · Jun 23, 2018

Stared at It. Poor thing sitting out in rain

Saddle up cover not completely waterproof. But them MS rains can hit hard

bronkenn · Jun 23, 2018

dsenatore said:
Indeed. Having done the full driveway restoration over 23 years ago it's slowly coming back to me, cussing included! The list was a lot shorter and lighter when I brainstormed what I "thought" it needed to get rolling again. Oh well... I certainly appreciate everyone's support that's chimed in! Back to it.

You did a restore when you were 2 years old? That is awesome! Ken

asappin · Jun 23, 2018

Road trip

Trailered the bronco 3 hours today to north MS. Using it as the ride off vehicle next week in our wedding

markw · Jun 23, 2018

congratulations on your wedding! Mark

Z Bronco · Jun 24, 2018

Almost finished the air induction set up. Checked and tightened all wiring connections (some were loose).

Skiddy · Jun 24, 2018

got my new license plate

Cortez · Jun 24, 2018

Installed a new timing cover and water pump - hope I took care of that pesky oil leak. Also hit the junkyard and lucked out finding a truck that had a recent remanufactured Saginaw power steering pump to replace my 30 year old leaking one. Two leaks resolved now on to the tranny and transfer case to seal them up.

Sminter33 · Jun 24, 2018

New paint, roll cage, seats, door and rear panels, speakers, led head and tail lights. Only a few more things to go until it’s done!

sprdv1 · Jun 24, 2018

Removed positive cable from battery. Damn thing wore itself out and was cracked all the way down causing no start

sprdv1 · Jun 24, 2018

Sminter33 said:
New paint, roll cage, seats, door and rear panels, speakers, led head and tail lights. Only a few more things to go until it’s done!

Looks great

sprdv1 · Jun 24, 2018

Skiddy said:
got my new license plate

Awwww. ;D

sprdv1 · Jun 24, 2018

asappin said:
Trailered the bronco 3 hours today to north MS. Using it as the ride off vehicle next week in our wedding

Damn it. Missed ya. Was up that direction yesterday

Had to run to Hardy AR. Got back to N MS area 1:30 ish

Visited the cousins in water valley overnight. Grilled out

Even messaged ole mean gene and he never called.

Congrats to y’all

asappin · Jun 24, 2018

sprdv1 said:
Damn it. Missed ya. Was up that direction yesterday

Had to run to Hardy AR. Got back to N MS area 1:30 ish

Visited the cousins in water valley overnight. Grilled out

Even messaged ole mean gene and he never called.

Congrats to y’all

There is a shop close to Water Valley with a bright orange Bronco and a blue one that I believe is for sale. Saw them on the way back but didn’t stop.

sprdv1 · Jun 25, 2018

asappin said:
There is a shop close to Water Valley with a bright orange Bronco and a blue one that I believe is for sale. Saw them on the way back but didn’t stop.

Didn't get into town..

came from north, 278 across to whatever roadthat was to cut me back to 7 Hwy

Maybe next time I'll have more time

rcmbronc · Jun 25, 2018

Got most of my rear end completed this weekend. Still have to add limit straps and bump stops.

Calibronc66 · Jun 25, 2018

Got rid of the plastic battery bracket and installed this and a new ididit tilt column with the WH lower shaft came out awesome.

Sent from my iPhone using Tapatalk

rspd505 · Jun 25, 2018

Played around with the rear wheel opening before I cut it off. I want to keep it uncut, but I also want a little bigger opening. I moved the opening forward an inch and raised it about 2 inches. I like it a lot!

Z Bronco · Jun 25, 2018

Finished the air induction system, cleaned the key cylinder for the ignition switch and it works better, and started the process of getting ready to cut an access panel in the floor for the EFI tank.

What have you done to your Bronco today?

Jr. Member

Sr. Member

Attachments

REBEL

Bronco Guy

Full Member

Attachments

Bronco Guru

Bronco Guru

Bronco Guru

Attachments

Bronco Guru

New Member

Attachments

REBEL

REBEL

REBEL

REBEL

Full Member

REBEL

Bronco Guru

Attachments

Full Member

Jr. Member

Attachments

Bronco Guru

Similar threads