• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Recent content by m_m70

  1. m_m70

    Help identifying Dana 44

    Also curious to see what the Marti report calls out, if anything, on the '69 & '70 that have been found to have the unicorn 44s.
  2. m_m70

    1970 Ford Bronco 302 - Carburetor, Distributer and Intake Manifold Leaks

    Great! Make sure you flush the crap out of the block too. Yeah I'd be spraying that down with some heavy degreaser and letting it soak then spray it down. Probably going to take a few rounds of that. Obviously avoid getting water around the carb and distributor cap. I usually just cover with...
  3. m_m70

    1970 Ford Bronco 302 - Carburetor, Distributer and Intake Manifold Leaks

    Good idea! If it aint broke..............
  4. m_m70

    1970 Ford Bronco 302 - Carburetor, Distributer and Intake Manifold Leaks

    Welcome!! You'll get a lot of opinions on this and here's mine. You can go three ways (or more) on this. 1 - spend a couple hundred bucks. - clean motor, rebuild carb and seal things up 2 - spend a thousand + - change to 4 bbl 3 - spend a few thousand + a bit more - EFI conversion Since you've...
  5. m_m70

    How bad do you want to check your bump steer?

    Agreed..................
  6. m_m70

    Wheel Alignment shop who have people used?

    What c-bushings did you install?? What is your truck doing other than "seeming to have too much camber"? Have you added anything else to the front end like drop pitman arm and drop trac-bar bracket or riser?? Hell, any pics (always fun)?? I used 7* with my 2.5" lift along with a drop pitman arm...
  7. m_m70

    23 gallon fuel tank- how to build. Plans

    Yup, times have changed for sure. Seen some tanks go for upwards of 2500.00 with skid plate, pump & shipping! Bit much for me, but this is and will always be just a hobby. I'll just stop more for gas, tell people it's a Bronco and not a jeep, and carry more on the trails! I may have a copy of...
  8. m_m70

    How bad do you want to check your bump steer?

    Love it. Reminds me of why I joined this site so long ago......
  9. m_m70

    Bronco won’t start- need your help!

    You can get a multimeter/voltmeter for less than any one of the parts you've asked about so I would start there and get the info to make a more informed decision on what parts you may or may not need.
  10. m_m70

    Blueprint Engine Update

    Glad to hear it's worked out!! Did your motor come with a flat tappet cam?? I would've thought they were roller cams in the new blocks.
  11. m_m70

    1974 Drivability issues (pass#2) - - {NEED HELP}

    this^^ and add more toe.
  12. m_m70

    1974 Drivability issues (pass#2) - - {NEED HELP}

    I have the same specs as you. 2.5" suspension and 1" body lift with 7* bushings. 33x12.5x15 that I run around 26psi. I do have my toe set at between 1/4 and 5/16 and it handles great at all speeds so you may want to increase that.
  13. m_m70

    66 Doors with 69 Internals

    No. you are not hearing that. Most people would stick with the door that works. The later door will not work with the '66 internals.
  14. m_m70

    Bronco won’t start- need your help!

    Here's what I would do after reading through this again from the start. 1. Check that there is power going from the battery to the starter relay. (Cable) 2. Disconnect the battery 3. Check the continuity of the negative cable 4. Find where the yellow wire terminates. If not used for anything...
Top