Community
Buy / Sell
James Duff Rust Bullet Sexton Offroad
Bronco Tech
Ford Bronco Parts - Classic Vintage Early Bronco Parts
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.
P

pocketlock

Contributor
Jr. Member
Joined
Last seen
Messages
124

Latest activity Postings Attachments Images About

    • P
      pocketlock replied to the thread 1970 Bronco Wheeler.
      Got the tire carrier put back together today. Apparently the cut and torch was a bit much. Gotta get the top to pull up a little now to...
      • IMG_8056.jpeg
      • IMG_8057.jpeg
      • IMG_8061.jpeg
    • P
      pocketlock replied to the thread 1970 Bronco Wheeler.
      I was stretching 1.5-2” forward so when I cut the factory buckets out, I left a small lip on the bottom to line the buckets up with the...
    • P
      pocketlock replied to the thread 1970 Bronco Wheeler.
      Reference point for which part? Sorry, there’s alot going on here haha.
    • P
      pocketlock replied to the thread 1970 Bronco Wheeler.
      Got my tow rig stuck in the back yard today troubleshooting some trailer brakes. So the bronco got a little workout pulling her out...
      • IMG_8051.png
      • IMG_8053.jpeg
    • P
      pocketlock replied to the thread 1970 Bronco Wheeler.
      Worked on the bronco a bit more today. Cut the passenger rocker out to work on getting it ready for the sliders. Test fit it up. Got my...
      • IMG_8025.jpeg
      • IMG_8026.jpeg
      • IMG_8036.jpeg
      • IMG_8035.jpeg
      • IMG_8034.jpeg
      • IMG_8024.jpeg
      • IMG_8023.jpeg
      • IMG_8022.jpeg
      • IMG_8021.jpeg
      • IMG_8020.jpeg
    • P
      pocketlock reacted to 73azbronco's post in the thread 1970 Bronco Wheeler with Like Like.
      wait, you had me at spray paint, seriously, or the spray paint using OEM style paint?
    • P
      pocketlock replied to the thread 1970 Bronco Wheeler.
      This was rustoleum lagoon spray paint with a 2k clear spray paint over top. If I did it again i don’t know that I’d do the 2k clear...
    • P
      pocketlock replied to the thread 1970 Bronco Wheeler.
      Big update and lots of photos. Got some 37" Sx-2 tires for this upcoming trip. Got them mounted and something didn't seem right with the...
      • 458754355_966689688553014_4311833854489100723_n (1).jpg
      • IMG_7825.jpeg
      • IMG_7791.jpeg
      • IMG_7740.jpeg
      • IMG_7738.jpeg
      • IMG_7905.jpeg
      • IMG_7929.jpeg
      • IMG_7927.jpeg
      • IMG_7993.jpeg
      • IMG_7957.jpeg
      • IMG_7972.jpeg
      • IMG_7973.jpeg
      • IMG_7980.jpeg
    • P
      pocketlock replied to the thread DIY bumper/tire carrier.
      There is a seal for the bottom. My instructor uses it and it isn’t messy outside of the housing.
    • P
      pocketlock replied to the thread DIY bumper/tire carrier.
      Ended up cutting the bumper stubs off to correct the angle of the swing arm. Previously it was parallel to the floor but that meant it...
      • IMG_7905.jpeg
      • IMG_7906.jpeg
      • IMG_7907.jpeg
      • IMG_7908.jpeg
      • IMG_7909.jpeg
    • P
      pocketlock reacted to FORD*DIEHARD's post in the thread DIY bumper/tire carrier with Like Like.
      I do not remember which vendor I bought the rear bumper from but I got it with just the spare tire mount as they only offered at the...
    • P
      pocketlock replied to the thread DIY bumper/tire carrier.
      That last part has been my motto through most of my self taught welding. A lot of it may not have been pretty. But it’s all held...
    • P
      pocketlock reacted to Yeller's post in the thread DIY bumper/tire carrier with Like Like.
      For less heat soak, more heat, move faster and push a straight bead with the wire tip directly in the groove. This will produce a narrow...
    • P
      pocketlock replied to the thread DIY bumper/tire carrier.
      He’s a younger guy in his 30s like me haha, funny you say that. Not saying you are wrong. He has been teaching me to tighten my bead up...
    • P
      pocketlock replied to the thread DIY bumper/tire carrier.
      These were welded flat, my welder is a Vulcan 215, the only adjustments on the unit are wire speed (A-G), wire size (0.25-0.35), and...
    Show older items
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Top