Search results

I'm in the middle of a half cab plow rig build and have a fisher hydrolic plow setup from a 71 bronco that did not have power steering. I really need pics of how the pump would mount on the motor with power steering and shots of how the lines run and control cables would route. Everything is in...

Well, finally dusted of the old girl and took her out of winter hibernation. When i first strated her up, i could hear a high pitched constant sound (sounds like those big cicada bugs that make that noise on hot summer days). thought it may be a fuel pump pooping out but it is coming from the...

http://classicbroncos.com/forums/showthread.php?t=67184&page=10&highlight=master+flow+air+compressor These are available again. I found a whole pallet at my local Costco in Colchester, VT for $49 each. Check or call your local Costco to see if they have them.

well after only being in the bronco for 3 years, the upper 4-5 rows of tubes on the passenger side and the upper 2-3 on the drivers side have begun to crack at the joint where the tubes enter the tank. i drove home from work and when i got there, i could hear a slight hissing sound and coolant...

Posted this on the off topic forum but it is tech info i'm sure someone knows. i need some input on my F150 tranny thanks http://classicbroncos.com/forums/showthread.php?p=845834&posted=1#post845834

http://www.pirate4x4.com/forum/showthread.php?t=528984 came across this on pirate not sure if he still has it or not but free is good!

update: got the cb installed over the weekend and antenna mounted to spare tire carrier(Wilson). checked signal with an swr meter and got 1 and 40 to come in at 1.75 and 20 at 1.5. scanning through some of the channels, i was able to pick up some chatter. all seemed well until i started up the...

so i've been working on a buddy's bronco doing a bunch of axle/brake upgrades and went to take it for a drive to get the cage done. i don't know much about auto trannies so i'm not sure what is wrong. i pulled out on the road and it seemed to do the 1-2 shift and reved up til my speed got to...

what is the correct yoke size for a 9" rear-1310 or 1330? mine is leaking pretty bad and grooved around the seal area. i have another yoke that looks like it was ready-sleaved. anyone done that or have a part number to do it? thx ed

When using a ferrule or sleave and tube nut to use with the flared end of a hard line to adapt it to AN (or JIC) do you use a single or double flare?

is there a source for just the resevoir. none of the parts places seem to be able to get just the tank without ordering the complete pump.

i'm looking for ideas on how to setup the e-brake equalizer bar on an older style kentrol glass tub. there is no forward bracket (the one that hangs down from the rear of the drivers side floor pan) that the front cable attaches to. there is also no provisions for the equalizer bracket and arm...

nothing came up using torque specs in the search... i'm working on a buddies d44 and had to pull the front carrier to change axle seals and need the bearing cap specs and cover bolt specs. do you use lock-tite on the cap bolts? looked like the last time they were put in, they used the red stuff...

i looked at a bunch of sites and can't find these codes both axles were pulled from a 76 or 77. Pretty sure 77 because the rear had the large banjo housing. i'd like to know what they have in them Front tag: 3.54 D7TA AYB 610026 3R Rear tag: WEM-E3 7EC 3 50 9 605F Gear ratios are obvious...

got to spend some quality time on the rig over thanksgiving. thought i'd share my cage build pics with you all. my plan was to use the front section of my smitty cage (main hoop and weld in front section---couldn't justify not using a few hundred bucks of tubing i already had) and add a family...

in Essex Vt on rt 15 this morning. had blacked out grill and looked pretty clean. anyone on the list or know who it is? wished i got a better look but the people in frot of me slammed on the brakes so it cut my rubber necking short :p

since the tranny/motor swap, my seedo hasn't worked. i figured the cable was gunked up or kinked so i pulled it from the transfer case and found the drive gear on the output shaft is free spinning. i'm able to stick my finger in and spin it on the shaft. spinning the gear on the end of the spedo...

any tips on testing for a bad fuel rail pressure regulator? i pulled the upper intake last night to pull the injectors for cleaning and want to test the regulator while it's easy to get to. crown vic fuel rails/regulator if it matters. the reason i suspect it is i've only got low 30's on the...

Well, had to do it. took the bronco for it's first road tip to my father in-laws to check things out since the engine/tranny/brake system upgrades (5.0 sefi from a crown vic, np435 and hydroboost with rear disk.) started out running a bit rough so i took it easy. figured i'd give the computer...

the last thing i ned to figure out is the the wiper wiring. from the harness to the wiper motor there are 5 wires. 1 goes to the dome light and the other 4 to the wiper motor (red, black, blue, white). i have a set of toms marine type replacement dual motors that had it's own switch. i want to...