What have you done to your Bronco today?

[ObscureMachine]

I got noticed out driving my bronco by a NW Bronco Roundup FB member!
Ordered an auto dimming rear view mirror.

 

[sprdv1]

Oil changed, tranny fluid topped off. DIFFS next

 

[Skiddy]

went to three different exhaust shops in town. no one could get it done by Tuesday am. drove to the next town over 65mph all the way
he will have it done tomorrow before we head out to MO;D

 

[sprdv1]

went to three different exhaust shops in town. no one could get it done by Tuesday am. drove to the next town over 65mph all the way
he will have it done tomorrow before we head out to MO;D

Oh lawd, why Missouri? LOL

I been WANTING to take mine to exhaust shop, but everything else is breaking the budget Uggh and not even left yet

 

[dave67fd]

DROVE to work ...it's getting a little chilly up here. Did hook up the blower motor and fixing a couple little things

Lookin good brother

 

[Skiddy]

Oh lawd, why Missouri? LOL

I been WANTING to take mine to exhaust shop, but everything else is breaking the budget Uggh and not even left yet

taking all the kids and grandkids to branson%)

 

[sprdv1]

All fluids checked, refreshed, or topped off.. Tire swap tomorrow ... let's GO

 

[sprdv1]

taking all the kids and grandkids to branson%)

Oh lawd, who's taking them back to OK when you go to OCBR?

 

[BronCowie]

All fluids checked, refreshed, or topped off.. Tire swap tomorrow ... let's GO

Let's see that bad boy with the tire swap.

 

[sprdv1]

Let's see that bad boy with the tire swap.

I'm gonna do a split pic w/em.. I HATE having to leave them small tires on it to fit in garage. But better to keep him Cool and Dry

Post up tomorrow

 

[66broncoCT]

No pictures but replaced my turn signal switch to get the rear passenger brake/turn signal working again. Some bonehead (me) left the wiring a little too close to the exhaust and it melted to it grounding out and burned out the switch that was working perfectly fine for 51 years....

 

[Crawdad]

Rear axle shaft repair sleeve

Installed new repair sleeves on my stock 28 spline rear axle shafts. You don't have to replace these after all in my humble opinion.

 

[Tiko433]

Ahhh
I just saw your repair thread. Kinda cool Nice skill to get it done. I used a sleeve to combat a rear main oil seal leak before

 

[Tiko433]

Started pulling trans. Every thing out of the way. I still have to unbolt bell housing and cross member. I have had success working the whole unit back tell the cross member clears the frame tabs then let the whole thing down.

 

[sprdv1]

ran it to the gas station to top it off w/fuel, and fill up the big jug of Fuel for OCBR and home and around the neighborhood trying to figure out why damn thing won't stick in park and not move...

Said fk it and now loaded on trailer, Cover over it cause the rain move din.

Figure out what's wrong with it Monday down in Hot Springs

 

[sprdv1]

Got the crawlers on today too before loading

 

[sprdv1]

Also, got the Hi Lift mounted on the cage w/the new Four Trek mounts.

Them things are Nice...

 

[ObscureMachine]

Also, got the Hi Lift mounted on the cage w/the new Four Trek mounts.

Them things are Nice...

Where did you mount the hi-lift. Not true if no pictures!

Didn't do much. Picked up the "right" tranny filter. Then cleaned the pan, painted the bottom of it the pan, the fill tube, and top of dip stick.

 

[nboost]

Got my EFI installed

 

[56f100bbw]

Bronco ride

I have friends that go on a motor cycle ride and I go for a bronco ride great time not far in the woods 3 or 4 times a week doesn't get any better