Search results

I have a freshly rebuilt Early Bronco low pinion Dana 44 up for sale. It has disc brakes, 30 spline chrome moly shafts with 760x spicer joints. Warn premium hubs. Yukon master rebuild kit with bearings and seals. Yukon 5.13 ring and pinion. ARB air locker. Arb heavy-duty diff cover. New ball...

Hi all I'm wanting to go with a bronco width hp dana 44 up front for front driveline and caster issues. My question is should I go with a complete full width and narrow it down and use all components from it?? Or should I buy the tbp mag 44 housing only from Tom's bronco parts? Keeping in mind i...

Hey all looking for a used set of trail doors preferably close by to Oregon. Willing to pay shipping for the right deal. Or come pick them up. Thanks!

Hey anyone run a currie antirock sway bar up front with long arms and coils?

Alright. Dont burn me at the stake! Anybody ever run a Jeep jk steering box on their bronco. They look very identical and in the jk world there are tons of steering gear options! Including ported boxes for hydro assist. Just curious if they are at all compatible??

Hi all probably a dumb question but I'm getting ready to install a nv4500 and an atlas II into my bronco. I already have all the transmission parts to do the swap but my atlas is still 3 weeks out. I thought about installing the nv4500 into the bronco then mating the Atlas II to it when i get...

Up for sale i have NP435 with adapter kit for dana 20 transfer case, Centerforce Dual friction Clutch disc, Dana 20 transfer case with Advanced Adapters heavy-duty output shaft. 2 Rear spicer drivelines, 1 front Driveline. Wild horses 4x4 gearbanger shifter, Toms Bronco Parts stainless steel...

Brand new Tom's bronco parts power steering kit. Comes with Saginaw pump, bracket, steering box, steering shaft coupler and all hoses and hardware. Great way to save some money and get a new in box kit. Shipping not included...

On the hunt for a good used Atlas II transfer case. Preferably 3.0:1 or 3.8:1 have cash and will travel to get it!! let me know!!

Hi there I'm looking at getting a High angle driveline from Jesse at High Angle Driveline down in CA. My question is how does it behave at higher speeds in high range? Is there major vibrations in the shaft at 40-50 mph range??

OK All anyone have detailed pics or description of how to mold the rear tail light guards to the side quarter panel armor??

To truss or not to truss? So I recently found out that I bent my ford 9" big bearing housing either by wheeling it too hard or during a slow roll over. I'm considering going with the Ruffstuff specialties ford 9" rear housings thats early bronco specific. Which is considerably stronger. But was...

Hey guys I am considering going from carb to factory ford maf efi. I currently have a ford racing 5.0l crate engine based off the 80s block. Its full roller with gt40x aluminum heads. its right around 350hp/ 350 ft lbs torque. I am wondering which intake upper and lower to use with this engine...

Hi there i am looking at a set of wheels for my bronco that are 17x8.5 with 4.63 inches of backspacing. I have Toms heavy duty heim steering and a dana 44 with disc brakes up front. i have a 3.5 in long travel lift and duff extended radius arms. i want to run a 35x12.5r17 tire. will these rims...

Hi guys I purchased a hardtop a while back and am in the process of tearing it down. Underneath the headliner I found a crudely installed plate patch in the roof panel where they had a rv type vent. Couldn't tell from the outside because it was bondoed and painted. Needless to say I need to put...

Hi all I have a Ford 9" Big bering axle and have 4.56 gears hooked up to a dana 20 and np435. Ive noticed that my Yukon Grizzly locker (only has 5k miles on it) has been popping more frequently on all sorts of terrain from asphalt to dirt roads to sand. It doesn't matter if I'm turning or not...

Hi there all My power-lok just failed. Spider gear teeth in the bottom of the diff. With 350 miles on it in 4x4. I am looking at replacing it with something more durable but still streetable. I do drive my rig on the pavement and on packed snowy roads in the winter. I have a Grizzly in the rear...

Where on the under cab body mount do you measure from to find the location of where the crossmember mounts. Do you measure from the center of the body mount or do you measure from the front of the mount where it is welded to the frame?? Picture or drawing would help immensely!

Would a dana 60 narrowed to 63" from drum surface to drum surface fit under my bronco with a dana 44 up front?? Or would the 60 be to wide?

What is the width of a early bronco 9" from drum surface to drum surface??