Search results

Does anyone have the NAPA part number for the replacement Ujoint on the lower steering column of a stock 76 with power steering? Mine has seen better days... Thanks! Jeff

Hi guys, Been a long time! I've got a bit of time to tinker with my 76 and remove the stock power steering box for some repairs. Question is when I remove the lower steering shaft, do I need to mark the position relative to the box flange or is it keyed? Pump has been leaking so it's very...

Nice day in Atlanta today. Trying to get motivated to start a new garage project, so I pulled my baby blue '76 out of the garage after 8 years. Last time I had it out, was 2006. Time flies. Rinsed her off, and she looked pretty good. Jeff

I travel a lot, and I'm always leaving my bronco in little pieces in my 'wife's' attached garage. I have a basement garage shop that a bit full right now, so no room to work. For the sake of harmony, I'm thinking of building my own Bronco garage. I've read some of the garage threads and got...

So I've finished the cage, got a raptor liner kit and about to begin to prep the inner tub for application, but I keep stalling. The stock 76 bronco in question is one I'm prepping for a daily driver for my 16 yo son. You remember, top off all summer, drive it rain or shine...just like I did...

My 76 ps Box (stock box, stock pump) is leaking at the fitting where the return line mates to the box. I've tightened it to the point I'm concerned I'm going to round the fitting. I think it may be a bit cross threaded. I have replaced the pump and the hoses. The originals were leaking in...

I want to replace the leaky gasket on my Ford 9" carrier housing. What other replacement parts will I need to swap at the same time? Rear axle seals? Anything else? Thanks, Jeff

Working on a cage for a stock '76 and would like to see the dash bar arrangements for folks with a dash pad. Also any comments on it. Primary driver on this one will be my fairly responsible 16 year old son, and travel will be 99% school and soccer practice. He gets his kicks on dirt bikes, so...

I have a '76 with a stock column, auto transmission. When I put it into park, it sometimes pops back out. (Rare) Also, when I have it in any gear besides park, the column shift housing collar will rotate approximately 1/2" back and forth. This creates some interesting situations while driving...

Searched for another thread on this, but very surprisingly did not find what I was looking for.. I have a '76 stocker that I am preparing for my 16 year old son to drive. Its pretty reliable at this point, but I am adding some safety and reliability things to it at this point. Cage, 3 pt...

Anyone got experience with Automotive wraps on EBs? Yes, I've seen pictures of a couple that were wrapped, and the pictures look good. How do they look in person? How well do they last? Looking for feedback? Pros? Cons?

Tonight I was driving the green bronco, and the brake warning light blipped a couple of times. It occurred during routine fairly hard deceleration making a turn into an adjacent street. Any meaning to this? The light does not stay on, and functions normally during start up of the vehicle...

Guys, Last night I was changing out a headlight on my '76 and while taking off the chrome trim ring, I found one of the sheet metal screws would spin, but not back out. I didn't plan on a project, so I just grabbed the other two screws and planned to put them back in and do the job another...

Am I right in expecting the red blue wire attached to the 'S' terminal of the starter relay to go +12V only when the ignition switch is moved to the 'start' position? Also, should the 'I' terminal of the starter relay have a solid (always on) +12V that it feeds to the brown wire and ultimately...

Hey Guys, Been a while. I've been working 24/7 for three months. Anyway, back in June, I drove my '76 (302/2V) into the Garage to replace the ball joints. Lifted it, replaced the joints, dropped it back down for test drive, and it would not start. It clicked and buzzed. I took the battery...

Finally got the knuckles reinstalled yesterday. Installed the axles and spindles today. Starting to reassemble the hub on the passenger side, and I'm not even close to being able to push the hub clutch mechanism in enough to get the snap ring on. It sounds like a hard metal 'clank', so don't...

The Spindle bearing kit came with a large Rubber seal, a plastic washer, a bearing/race, and a small rubber seal. 1)What's the small rubber seal, and where does it go? There wasn't one in the hub / spindle assy when I disassembled it. It has a V type body. How do I orient it? 2) Also, the...

In the shop, with your son, working on the Bronco...nothing like it.

Reassembling a hub / disc assembly on a '76 D44. Should I reuse the wheel lugs if they look OK, or is it a good policy to just replace them every time the disc is removed?

What size bolt is used in the '76 knuckle wheel stop? Is it grade 5? What size drill and tap should be used to remove a damaged one?