Search results

looking for a good solid straight liftgate with hinges attached, internals not important already have those.

After some searching found these speaker enclousures. I was well surprised how heavy duty this plastic enclosure was along with the mounting hardware. Site says its made for two 6.5" speakers but I put two 6x9's with 45 watts rms per speaker. Sounds awesome, mounts rock steady to the roll...

Like I said, a big forum thank you. Lots of awesome people and awesome information. Had to ask a few dumb questions and an opinion or two here and there. I am cruising now;D;D

So my nv3550 rattles something terrible, read every article on here I think about the nv3550 and I come across this web site some how in a link. Never saw this info on this site and it's the weekend didn't figure I get a response by email from them before the weekend was up. This website says...

Going through my front end getting it ready for an alignment, new ball joints and the like. I want to change from bolts that hold the spindle on to press in studs from the back and would like to know what's worked for y'all, so I can get it right the first time without trial and error. I have...

Not much on color choice and/or design so I'm asking for some ideas on interior color choices and layout for bucket seats (higher back type and don't know if i am gonna use headrest or not yet), door panels, quarter panels, a knock off tuffy center console ect. Received several opinions from...

Found the stainless ones on ebay but I am more interested in the black plastic, can't find any direct fits. Anybody know of or have modified some plastic bed rail caps that would work for a early bronco?

Mounted my new fiberglass hood and all my gaps and everything is good to go but it is bowed in the center / sits higher than the fenders in the middle about 3/8 of an inch or so. No matter what I do it still does the same thing. Pretty sure I already know the answer but is there any way to...

I assume that these holes fit stock mirrors that the vendors offer? what is the big hole for? Need to duplicate those holes on passenger side b4 paint if they are. If I duplicate these holes on the passenger side will I be able to see out of it or will the vent window/trim be in the way? If the...

Sale'n a full circle Ron Davis fan shroud for stock body lift. Ordered from WH and ordered the wrong one, UPS gonna cost me $75 to send it back, so thought I'd offer it up for sale here, n hopes of someone closer needs one. Installed long enough to see it wouldn't work. If close enough will...

Installed DUI distributor on my work in progress and its crooked / leaning. 96 exploder motor that I am carbing. distributor installs and fully seats like its supposed to, just a wiggle and a bump, falls right in. been over distributor with a fine tooth comb, cap on straight, rotor rotates...

Does the D.U.I. distributor fit with explorer serp? Done quite a bit of searching and didn't come up with a definitive answer. Know I'm good on top with 1in body lift and cowl induction hood. Just wondering on the explorer serp brackets and heater elbow in the intake. Read it stands kinda high...

Got a new cowl hood and I want to open up the back to help move air in and out of the engine compartment. How much or little can u cut out the back of the cowl or cut a few holes with a 3" hole saw? If drilling holes is the route to go anybody found any trim rings to dress the holes up and...

Need a starting point measurement, till I can get my doors on, between the top of the fender and where the windshield mounts. I remember less than a 1/4" almost touching is that right?

installing a 96 explorer engine and found the two holes in the block that need plugging 1). just behind the intake on top side and 2). one on passenger side of the block. Question is, are there any holes on the backside of the head that need plugging? I've poked around in them with a pic and...

interested in ways members rustproof restore nuts and bolts. got a black oxide kit to do them with and a little disappointed in the results. wondering of other ways to restore/rustproof them. one i heard of is to get them good and hot through and through and dump them in transmission fluid...

looking for a good/tight set of door hinges. could be stock/stainless/lift offs. let me know what u got.

read quite a few post about the subject, gas smell outside the vehicle, raw gas running into vent line, charcoal canister, expansion tank ect ect. and had an idea and was wondering if its a bad idea or not and wanted some opinions. my plan is drill a hole into the top of the fuel filler pipe as...

i have a rebuilt (by cordone) factory steering box never installed, its a 6 turn. $350 includes shipping usps. PM me or email jon_eds@yahoo.com

I have a body tub minus front clip and assorted parts for repair of the tub that i am interested in selling. tub needs work but is in descent shape. floor pans replaced by PO and i have done some rust repair, patching. parts that need replacing: passenger kick panel, possibly passenger inner...