Search results

1971 Bronco 9". Small bearing, Small brake. 3.50 gear ratio, track lock LS. Passenger axle is bad (bearing wont seat tight). Not a lot to compare prices to, so make me an offer.

Does any manufacture make a reservoir shock that will work with our factory front mount (stud/eye)?

I am having an issue with brake lights not working. '71 model, turn signals work fine. the plug at the brake pedal is plugged in. Hoping someone has had a similar issue, or suggestions on where to start looking. Thanks in advance, Mike

Just got my gauge cluster back from Classy Gauges (thank you Kevin) i had the alt gauge changed to a volt gauge (doing a 3G conversion). it was recommended by a couple people that I remove the the wire that served the Alt gauge from the cab. My question is exactly what wire under the hood do I...

After bending another NEW tierod i want to do a TRO on the '71. The question i have is, when drilling the top taper does the taper have to be so precise that i need to take the knuckles off and have a machine shop redrill them ?

I have an issue with my gauge cluster. My temp, and oil pressure gauges are pegging out on the high side. The gas gauge doesn't work, and hasnt for a couple years so I bought an aftermarket gas gauge. It works just fine. Here recently whenever I turn the key on the temp gauge pegs out on the...

Just installed a flaming river tilt column. Connected the wires as per the instructions, with the exception of the two horn wires (I don't have a horn yet) and the flasher wire (flasher is on the dash). None of the turn signals work, but when I apply the brakes all four lights come on ????. I'm...

Went to drive the Bronco today hit the key, it started, and the starter will not disengage ? Had to mad dash around to the front and disconnect the battery. Anyone had this issue ? I suspect it's the ignition switch, but not sure. Thanks in advance, Mike

Next upgrade will be a power steering kit. I have looked at and called some of our venders, and here is the dilemma/questions 1. Duffs power steering conversion kit, rebuilt steering box, with some "tweeks" to make it even better (salesman wouldn't say what that means), 3 3/4 turn box. 2. Toms...

As stated i need to replace all my driveshaft U joints on my 71. Is there a preferred, or do not use brand ?

Has anyone switched from FI Tech to Holley Sniper ? I am very unhappy with my FI Tech, looking to go with Holley Sniper.

Anyone in Northwest Oregon/Southwest Washington planning any outings? I finally have the bronco ready for some trails (351, FI Tech EFI, 2 1/2" susp lift, 2" body, 35" tires, still have factory 3 speed but not for long) anyone interested in having rookie wheeler tag along (Browns camp, Estacada...

Quick question about engine temp. I have a 97 351, my engine temp has never exceded 175 degrees even in 100+ weather. I was on another site where they saying if your engine temp isn't running 190-210 then you are leaving some performance on the table. My question is should I change to a 190...

My 71 the turn signals are working but no brake lights. I'm not sure if the hazard lights have anything to do with it but I believe I did have brake lights even though the hazards have never worked in the 26 years I have owned the bronco. Hoping someone here has had a similar experience and...

Just finished my fi tech install. Went through to recheck my timing, the mech advance comes up to about 32-34 at 2500 rpm. BUT, after returning to idle the timing seems to stay up around 22-24 btdc. I assumed the timing would drop back to the initial 12-14 btdc that I have it set at ? Is my...

Just installed a 2.5 suspension lift (progressive rate coils, adjustable track bar) I set the toe in to 3/16. Took it for a test spin and the steering is VERY unhappy ! Feels like it over reacts to the steering wheel, and hitting bumps seems to divert the truck. I expected it not to drive...

We got a little snow here in the great Pacific Northwest, so obviously i took the bronco out to play. I locked in the hubs and was driving in 2 high. i can hear a low dull wump wump noise from the front end, put it in 4 high same thing. Put it back in 2 high, disengaged the hubs no noise. The...

Trying to figure out how to load photos.

Bone head move on my part, but I broke the Ez out off in the door hinge backing plate. I am hoping the someone might have had a similar situation, or any recomendation for getting it out ? Thanks, Mike

So, my fuel gauge has never worked the whole 25 + years I have owned the Bronco. Decided I would spend the time to get this fuel gauge working, searched tech articles on this forum, thought I had a pretty good idea of how to trouble shoot the issue. Tested this and that came to the conclusion I...