CA WH Drive line.

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 3, 2016

• #1

I have a Tom Woods extreme drive line from WH. Has less than 300 mile on it, before I started a restoration and ended up needing a 1350's

Has u joints installed 1310

34.5in.


New from WH is 369
Asking 250

Pm or call 209-298-123two

 

Last edited: Jan 10, 2016

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 5, 2016

• #2

Bump to the top

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 6, 2016

• #3

Bump up!

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 7, 2016

• #4

Pm's answered.

 

mickphatmac

Sr. Member

Joined

Jul 26, 2006

Messages

520

• Jan 7, 2016

• #5

How much suspension lift were you running, and did you have your rear axle moved back at all?

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 8, 2016

• #6

5.5 lift, probably slightly less do to rear weight( my protofab bumper). But the axle is in the stock location.

 

Last edited: Jan 8, 2016

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 8, 2016

• #7

Bump to the top

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 10, 2016

• #8

Bump go Sunday.

 

rednck21

Newbie

Joined

Feb 27, 2002

Messages

3,915

• Jan 10, 2016

• #9

Is that the working measurement or collapsed?

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 10, 2016

• #10

Collapsed.

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 11, 2016

• #11

35.4 working measurement.

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 12, 2016

• #12

Bump to the top.

 

D

duffymahoney

Contributor

Bronco Guru

Joined

Apr 26, 2015

Messages

2,595

• Jan 12, 2016

• #13

I need to install my motor and tranny. I have zero idea if this would work for me or not! What tranny was this for? Longer or shorter then stock?

 

rednck21

Newbie

Joined

Feb 27, 2002

Messages

3,915

• Jan 12, 2016

• #14

It's too long for my rig. I need about 34.5" working measurement..

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 14, 2016

• #15

To the top.

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 16, 2016

• #16

Saturday bump

 

OP

OP

KyddsPly

Sr. Member

Joined

Nov 30, 2012

Messages

941

• Jan 17, 2016

• #17

Sold today. Thank you