Community
Message Forum
Photo Gallery
Event Calendar
Book Reviews
Bronco Wallpaper
Bronco FAQ
Link Back to CB!
Photo Gallery
Event Calendar
Book Reviews
Bronco Wallpaper
Bronco FAQ
Link Back to CB!
Buy / Sell
Bronco Tech
3 Arm Wiper Setup
Fix Motor Mount
Roll Cage Braces
Throttle Body 65mm
Wheel Alignment
Heat Riser Replacement
Vent Window Repair
Center Console Mount
Straighten Bumper
Ford 6R80 6 spd
More Tech...
Fix Motor Mount
Roll Cage Braces
Throttle Body 65mm
Wheel Alignment
Heat Riser Replacement
Vent Window Repair
Center Console Mount
Straighten Bumper
Ford 6R80 6 spd
More Tech...
-
Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!If you have problems registering or can't log into your account, please contact Admin.
pcf_mark
Bronco Guru
- Joined
- Last seen
- Messages
- 3,594
Latest activity Postings Images Garage items About
-
-
pcf_mark replied to the thread Throw-Out Bearing Rattle.I would put a stethoscope on the trans case and bell housing while someone presses the pedal lightly with the engine running. It could... -
pcf_mark replied to the thread Hosed again, 351w with serpentine and reversed inlete/outlets..I fabricated an upper and lower pipe from exhaust tubing. I had a few 90 and 180 degree bends laying around I welded them into the...
-
pcf_mark replied to the thread Oil drain not drilled in cylinder head?.if I did not see the picture I would not have believed it. The holes are machined in a gang fixture that is hitting a lot of holes all...
-
pcf_mark replied to the thread Advanced Death Wobble.People say you can't hear text but this was pretty close!
-
Sorry to muddy up your thread with another long story Mark, but figured this was as good a spot as any to throw in my experiences over...
-
Rotating tires would be only slightly less easy. Necessary, but rotating the tires would be quicker and easier. Always good to know...
-
pcf_mark replied to the thread Oil viscosity.Fantastic article! Thanks for sharing. I used to run 600 lb open spring pressure on the street and w/o VR1 and running the engine...
-
This ^^^. Started using 10W-30 VR1 years ago after coming across this info. Bit of a long read, but worth it. Especially what can...
-
pcf_mark replied to the thread Advanced Death Wobble.Thanks for the detailed education. I'll continue to probe for something loose maybe I missed something the first few times I looked. I...
-
pcf_mark replied to the thread Oil viscosity.Regardless of viscosity (10W-30W is my go to) I would recommend Valvoline VR1 oil. It is very high quality race/off road oil with a...
-
pcf_mark replied to the thread engine advice.I'm a huge fan of used Explorer 5.0 engines. With 150k the cylinders still look great. You get roller valvetrain, p style heads and...
-
pcf_mark replied to the thread Advanced Death Wobble.I'm located in PA so I could not possibly be father away but thank you! I had an alignment when I replaced my drag link and there were...
-
I have been chasing death wobble for about a year maybe longer. This is somewhat unique maybe you have some insight because it is...
-
pcf_mark replied to the thread Source of oil residue.On shut down the hot engine puts out hot vapors that rise and if that is a vacuum hose not rated for oil it can sweat like that.
-
pcf_mark replied to the thread Explorer 5.0 Sensors.Also if you can put the Explorer sensor in the same relative location as it was on the Explorer sensor. I had mine in the intake behind...
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
