Community
Buy / Sell
James Duff Rust Bullet Sexton Offroad
Bronco Tech
Ford Bronco Parts - Classic Vintage Early Bronco Parts
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

hunter1's latest activity

  • hunter1
    hunter1 posted the thread TN Column shift reverse/backup light switch bracket in Wanted - 66-77 Bronco Parts.
    I need the little clamped on bracket that holds the reverse light switch to the column. Let me know what you got. Thanks
    • reverse light switch.jpg
  • hunter1
    hunter1 replied to the thread AL Remote power steering reservoir.
    This is what I used. Had to weld a nipple on it for the pump feed hose and re-located the fill so I could lay it down on the wheel tub...
    • HB hoses.jpg
  • hunter1
    hunter1 reacted to Splash440's post in the thread 75 Bronco Restoration with Like Like.
    After doing the passenger side the driver's side was a little easier. I spent a lot of time getting it all aligned with clamps before I...
  • hunter1
    hunter1 replied to the thread Finally getting started.
    Installed a Motorcraft temp sending unit today. Checked temp with an IR heat gun at the sender and spot on at the gauge 190* sitting...
  • hunter1
    hunter1 reacted to Yeller's post in the thread Finally getting started with Like Like.
    Looking good! starting and moving always a good motivator :) FYI: There is now a 33x9.50-15 available once again Kenda has them in...
  • hunter1
    hunter1 replied to the thread What have you done to your Bronco today?.
    Installed a Motorcraft temperature sending unit today. Temp gauge works correctly now.
  • hunter1
    hunter1 replied to the thread No Brakes.
    5/8- same as the original shaft.
  • hunter1
    hunter1 replied to the thread No Brakes.
    That was a roll pin in the shaft but have since pressed a hardened dowel in it and spot welded on either end. The shaft is mildly...
  • hunter1
    hunter1 reacted to gnsteam's post in the thread Project: 76, Orange Special Decor with Like Like.
    I had a pretty productive New Years Eve day in the garage. I finished up the mounting of the washer / radiator overflow tank. You will...
  • hunter1
    hunter1 replied to the thread No Brakes.
    I'll be running 33's when it's all said and done. Worth trying a 1-1/8" bore MC or do you think it would be a disappointment?
  • hunter1
    hunter1 replied to the thread No Brakes.
    Was told it was from a Mustang Cobra when I bought it used??
  • hunter1
    hunter1 replied to the thread No Brakes.
    I currently do not have a bushing in the pushrod. My linkage is modified as I moved the HB out over the drivers wheel tub, so I may not...
    • IMG_2742.jpeg
    • IMG_1487.jpeg
    • IMG_1491.jpeg
  • hunter1
    hunter1 replied to the thread No Brakes.
    I’m used to a lot more pedal driving my truck. The piston in my MC is one inch. It is some type of GM based design but with a screw down...
  • hunter1
    hunter1 replied to the thread No Brakes.
    1 inch bore. Front brakes are some GM based caliper that comes with disc conversion kit from most of the vendors on here. Not really...
  • hunter1
    hunter1 replied to the thread No Brakes.
    Brake pedal still returns very slowly. I have checked the return line from the HB and it is working fine. Do not see any air bubbles in...
Show older items
Top