• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Recent content by Jeff10

  1. Jeff10

    GIVEAWAY ClassicBroncos.com Giveaway! - Duffs - Modern Door Checks - 2 winners! - Ends 10/8/22

    I would be proud to rock a set of those! Great idea for a new product. Thanks for the opportunity! Jeff
  2. Jeff10

    NP435 - Very Hard Shifting

    Hi Everyone, Thanks for all the suggestions. I'm anxious to see what can be done to improve it. I'll keep you posted. Jeff
  3. Jeff10

    NP435 - Very Hard Shifting

    EPB72 and Broncobowsher, Thanks for all the ideas. I'll try to get pictures tomorrow. The collar is pretty low... not much mechanical advantage. Not sure there is enough of the original shaft left to move the shifter collar up. I've loosened/adjusted the pivot points on the Gear Banger. The...
  4. Jeff10

    NP435 - Very Hard Shifting

    Hi Jon, That is another topic. Lol The clutch doesn't really engage until the pedal is about 80% out from being depressed fully. I originally thought it might be a clutch adjustment issue, and it still may. Wouldn't the way it is acting now indicate that when the pedal is fully depressed that...
  5. Jeff10

    NP435 - Very Hard Shifting

    Hi Everyone, This probably isn't the best way to approach this problem; but, I am going post some information to see if anyone else has related experience that might help. In our '70 we have a NP435 mated to a 347 Stroker. The Bronco hasn't been driven anywhere other than up on the trailer a...
  6. Jeff10

    IN Custom Dash with Gauges

    Hi, I'll send you a PM. Jeff
  7. Jeff10

    IN Custom Dash with Gauges

    Hi, PM sent for the shipping cost. The hinge must have been for some type of smart device or GPS. It was attached to the dash when I bought the Bronco. Thanks, Jeff
  8. Jeff10

    IN Custom Dash with Gauges

    Hi, Senders for oil pressure and engine temperature will now be included, too. Thanks, Jeff
  9. Jeff10

    IN Stock Rear Seat - Black

    Hi, I guess the pricing must have fallen off when CB changed servers. The last time I priced it to anyone it was $475 plus shipping. Thanks, Jeff
  10. Jeff10

    IN Stock Rear Seat - Black

    Hi, I do still have it. Jeff
  11. Jeff10

    2022 NORRA article

    Hi Todd, Great article. I always enjoy reading your take on things related to Broncos. Thanks for for doing so much to support our community! Jeff
  12. Jeff10

    Bronco Script Sill Plate Install Recommendations

    Hi Hyghlndr, Thanks very much for the advice. Sounds like a good plan. Jeff
  13. Jeff10

    Bronco Script Sill Plate Install Recommendations

    Hi Everyone, I did a little searching for this; but, I can't really figure which sill plates I have, or the best way to install them. I purchased some stainless steel script sill plates from another member a few years ago. Just now getting around to installing them. The sill plates have holes...
  14. Jeff10

    Fiberglass hood, run stock latch assembly?

    Hi Everyone, I thought I would resurrect this thread. I have a fiberglass hood with pins on the corner on the '70. No latch or spring installed at the moment. I do have some of the parts in chrome, so I was planning on installing the secondary latch. I don't think that I have everything...
  15. Jeff10

    2022 Mex1000 videos

    Hi Phil, Awesome video. Great action on the first video that I watched. Pretty exciting! Thanks for all of the time and effort to share everything with us. Jeff
Top