• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Recent content by JWMcCrary

  1. JWMcCrary

    Best radiator for cooling 393/408 ?

    There are threads doing a search but they are several years old. I have a stock replacement Ron Davis radiator that I have been running since 2005, nothing special other than aluminum. I'm starting to see temps when crawling as high as 215-220. Used to never go above 200. Explorer serp setup...
  2. JWMcCrary

    My holley sniper experience is a failure

    I'm not sure what's up with some of the EFI systems. I put the Terminator on my 73 right after it came out in 2013, still running it. I've had a bad oxygen sensor and twice had to replace the TPS but it runs like a scalded ape on my 393. I also had electronic board in the dual sync distributor...
  3. JWMcCrary

    AR OCBR 2023 Parts Swap, Sale, Beg, Buy, Borrow.... POST UP

    I have 2 Detroit lockers, both 31 spline. Can bring to OCBR One of them I bought new in 2005, right before United by Bronco in 2022 I stripped the splines off the axle on the left side, I replaced the axles and on test drive seemed like it was popping more than normal. This text drive was on...
  4. JWMcCrary

    Dana 20 T-shift rod seals

    I've changed the seal on my cold duck which is a T shift rail, it's tough getting the old seal out and it's on the bottom and easy to get to the way the duck is clocked. So, yes it can be done on T shift rails but it won't be easy. I put some wheel bearing grease on the rubber seal when I put...
  5. JWMcCrary

    Bobcat 8274 winch bumper

    I don't remember having to remove a bolt from the steering box but its been a few years. I do know that it lines up perfect when you get it in there. Some broncos need 1 hole drilled on the passenger side, I do remember that because I had to do it on my 73 with the standard Bailie winch bumper...
  6. JWMcCrary

    Seems to not be a lot of 8274 bumpers?

    Bailie Bilt makes a bumper for the 8274
  7. JWMcCrary

    Need 9 inch bearing part numbers

    Thanks Guys
  8. JWMcCrary

    Need 9 inch bearing part numbers

    Can somebody give me the carrier bearing/race part numbers for the 9 inch standard Bronco case? Timken numbers?
  9. JWMcCrary

    Ram Assist Steering

    I have the West Texas Offroad ram assist on both of my broncos, one has hydroboost as well with a dual return pump (the one with the aluminum cooler has hydroboost). Both have saginaw pumps without an external reservoir and use ported stock EB steering boxes. What I did do that I'm confident...
  10. JWMcCrary

    OCBR 2022 Raffle Night

    Good pics Super Dave
  11. JWMcCrary

    Dana 44 Help

    IF you were upgrading from a stock 3.50 geared to D44 to 4,11 you would need all he same parts you are missing. Based on what you describe ou are wanting I would buy all new parts and put it together.
  12. JWMcCrary

    80:1 crawl with manual transmission…Thoughts?

    Both of my Broncos have cold duck doublers with C4, I would hate to have to go back, it sure makes easing over and around tight tough spots a lot easier. 2.46(C4) X 2.46(CD) X 3.15(D20) X 4.30 = 82:1 73 with 393 37 inch tires 2,46(C4) X 2.46(CD) X 2.46(D20) X 4.88 = 72:1 75 with 302 38...
  13. JWMcCrary

    2 vs 4 Barrell EFI?

    Hopefully an injector fixes your problem, but, to answer you initial question the 2V sniper works fine even with a mild cam. I have it on my 75 and never had an issue. I wish I could say the same for the Terminator on my other Bronco, never ending tuning. For a stock motor I wouldn't hesitate on...
Top