• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Stock passenger EB seat latch mod

snick

Contributor
Full Member
Joined
Feb 5, 2015
Messages
158
Wanted to share a mod that took me down a very long rabbit hole but maybe it’ll help someone out that is interested in doing something similar. This forum has greatly helped me out and saved me hundreds of hours with countless mods so trying to pay it forward. My apologies in advance for this book length post but want to give the full back story.

I looked at all the options for aftermarket seats but ultimately decided I really like the classic look of stock EB seats. So I foolishly came to the conclusion that I could modify, restore and reupholster my seats in a timely manner and not break the bank (truly laughable).

Besides adding 69 mustang headrests, which is well documented in many threads, I decided that I wanted to add a passenger seat, passenger DOOR-SIDE latch release so that someone accessing the rear seat could fold and tumble the passenger side and not have to reach over the seat and pull the awkward location lever. Additionally, with my tuffy center console (8” wide), reaching the latch was almost impossible from both the driver and passenger sides due to the console taking up and blocking all space to reach the lever.

Additional goals with the passenger seat:
- maintain complete fold and tumble capability with 69 headrests for rear seat access. The additional height of the headrests causes them to hit the dash when folding down the upper seat frame
- new stock appearing latch release lever located in the stock EB location, but switched to the passenger side of the seat
- keep the stock location passenger latch location and function so someone sitting in the back seat can easily reach the latch fold and tumble the seat to get out

So after researching all possible stock ford seat donors (Mostly different year mustang seats) I found that I needed the latch bracket and additional latch componets from the passenger seat of 1970 mustang high back seat (yes - the high back passenger seat from a 70 mustang). This is the only year ford make and model I found with the same passenger seat latch release bracket and related components in the same location as an EB stock seat.

I welded the mustang bracket into the EB seat frame, assembled the latch mechanism and then I welded a curved steel rod between the new 70 mustang mechanism/bracket and the stock EB mechanism/bracket. I think the pics/video will probably do a better job explaining. I then had everything blasted and powder coated and then reupholstered them with all new foam and upholstery. Overall I’m happy with how they turned out. One pricey but very cool option I’d encourage others to co sided that would have accomplished most of the goals I had is the Lick Creek passenger seat bracket that folds and rotates forward. I may have gone this route but it wasn’t on the market yet when I started the journey down this rat hole. I’ll try to post some pics and maybe a video of the finished installed seat when I get a chance.

Note on the video: before I hacked up my good condition passenger seat frame I tested out my plan on an old 68 mustang driver side seat frame that I had lying around to make sure everything was going to work. The video was shot using the test mustang frame. I’m including it to show the latch mechanism in action and curved steel rod that connects the 2 brackets. Obviously the actual latch locations (much higher on the mustang frame) and brackets are slightly different.
 

Attachments

  • IMG_0275.jpeg
    IMG_0275.jpeg
    276.9 KB · Views: 117
  • IMG_2918.mov
    25.4 MB
  • IMG_0336.jpeg
    IMG_0336.jpeg
    266.8 KB · Views: 123
  • IMG_0333.jpeg
    IMG_0333.jpeg
    390.3 KB · Views: 121
  • IMG_0338.jpeg
    IMG_0338.jpeg
    258.4 KB · Views: 111
  • IMG_0332.jpeg
    IMG_0332.jpeg
    362.9 KB · Views: 124
  • IMG_0279.jpeg
    IMG_0279.jpeg
    248.2 KB · Views: 116
  • IMG_0276.jpeg
    IMG_0276.jpeg
    252.8 KB · Views: 102
  • IMG_0268.jpeg
    IMG_0268.jpeg
    226 KB · Views: 117
  • IMG_0269.jpeg
    IMG_0269.jpeg
    162.3 KB · Views: 118

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
Great project!

Looking forward to see the finished product in action.
 
OP
OP
S

snick

Contributor
Full Member
Joined
Feb 5, 2015
Messages
158
Here are some pics of my finished seats. I used new foam from TMI and new covers from Tom’s. It was my first time doing any upholstery. One recommendation to anyone thinking about redoing their stock seats with new foam - spend a little more on the TMI foam that has the listing wire molded into the foam, it really helps for multiple reasons.

Adding the bracket (see first post) to the passenger seat does not allow the upper seat back to fold down as flat as a stock EB passenger seat which resulted in needing to push the passenger seat with the 69 mustang headrests back even further to allow the seat to fold and tumble without hitting the dash. I used both the driver side and passenger side seat brackets that BigJhoov sells to push the seats back as far as the brackets allowed. I highly recommend his brackets. They’re thick steel and allow you to use the factory seat mounting locations and push your seats back either 2 or 4”.
 

Attachments

  • IMG_2706.jpeg
    IMG_2706.jpeg
    330.9 KB · Views: 143
  • IMG_2707.jpeg
    IMG_2707.jpeg
    332.3 KB · Views: 146
  • IMG_2708.jpeg
    IMG_2708.jpeg
    278.6 KB · Views: 154

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
Great looking mod. I didn't even know about being able to add headrests to stock seats. Yet another project to add to the list.
 
Top