Search results

I'm loving these doors, but the latches are rattling like a can full of nuts and bolts. Tom's is trying to find a fix for me, but I wondered if anyone else has experienced this, and f so, what you did to quiet them down. Thanks in advance.

Just installed 37s on my 72 and it looks like some trimming will be necessary. Just curious how much others have needed to trim. I know the rock sliders and some sharp areas where the tub ties in need to be trimmed. Sent from my iPhone using Tapatalk

BC Broncos used to sell a pre-bent fuel line, but I'm told they no longer carry it. Anyone have another source for this? This would be for a 72. I see that LMC sells soemthing for a 77, but unsure if this will work for the 72.

Looking for some used supports. Anyone have some from an old top?

Bought a set of doors that have the holes covered where a bolt should come through the door and into the wing window assembly. Can someone measure and tell me where these holes should be? Pictures would be helpful as well. Thanks

I have two spares that appear to be a left and right. The bearing surface of on is approximately is 1.53” and the other is 1.375”. Any idea why they are different? Sent from my iPhone using Tapatalk

Just installed a new ARB front locker and dual compressor. When I started the compressor it ran fine. When I turned on the locker switch it stopped and I was checking for leaks when the compressor started making a weird moaning noise. Now the compressor won’t even work on its own. I checked...

Helping a friend diagnose this issue. NP435 replacing a stock tranny. New clutch (installed correctly). Clutch disc and throw out bearing slid along input shaft easily before assembly. Now it won’t disengage. Disconnected adjuster from clutch fork and no change. Thoughts and ideas? Sent from...

The rods I have are curved. Can’t seem to tell if that curve should follow the outside body line or not. They’re not lining up with the door latch that way, but the other way places them across the window track. Anyone have a picture? Sent from my iPhone using Tapatalk

I asked Jon about this several months ago and he wasn't sure if there was enough interest to do so, but was curious if others see value in Jon adding forums for all the earlier generations of Bronco? I know a lot of people have Broncos other than the Gen 1. I've been building a 78 for my...

Looking for a good set of doors for my 72. Bought some shells thinking they would work, but the more I dig in, the more I just want to find something else. In WA State.

For those who have rebuilt one of these, I am installing the adapter seal and it's not real clear on the orientation of the seal. How do you know the correct way to install it? It's the double lip seal, so I'm not sure it really matters. Want to ensure I don't get transmission fluid in the...

Anyone have a tried and true plier for the large snap rings with no holes for a traditional snap ring plier?

Ive been having issues with my Bronco since last spring. A serious vibration occurs under load. I have an Explorer 5.0 (Fairly fresh build) with an NP435 behind it. As usual, I typically start off in second and recently I’ve needed to rev the engine to keep it from stalling. Second and third...

Just finishing up my project and would like to wire the headlights and turn signals for a wall plug in. Anyone done this or have some words of wisdom as to how? Thanks in advance.

Need a set to complete my wall art project. Let me know if you have a set and how much you want for them. Thanks Chuck

Anyone have a trick to getting the color out without ruining the chrome? This is nearly new set that the color fell out of the D.

Need all four. Hoping someone has a wrecked or junk grill they can salvage these from for me. Sent from my iPhone using Tapatalk

I need the later style turn signal buckets. Trim doesn’t need to be perfect. Sent from my iPhone using Tapatalk

I know it’s not likely, but anyone coming from Oklahoma to Washington State with trailer space? Sent from my iPhone using Tapatalk