Found a 67 U13 let's hear some prices

[k13evin]

Found this for sell. What's the going rate for a 67 u13

 

[Beer and Fish]

Nice! I'll wait for the other guys to chime in!

 

[jamesf7278]

I'll say that door striker weld job is priceless!!!

 

[thegreatjustino]

Next to no value as a U13 since it's cut, lifted, has doors (incorrect ones for '67 at that), and has a top.

You'd spend a fortune turning that back into a true U13.

Fender aprons rusted out, shoddy work on the striker. I'd guess there are several other hidden issues to be addressed. I'd offer no more than you would for any run of the mill Bronco.

 

[KAllen]

12,500 canton ga

 

[k13evin]

12,500 canton ga

That be it.
Yeah the striker weld job is nice.

 

[BajaFresh75]

I'd get a Marti and pay for the same day service, then see if it came from the factory with doors. If so, I'd pass, if not and you want a '67 U13, I'd make a play on it. YOU can sell the top and doors and put it towards inserts and backing plates. Fixing striker optional, since it's not being used.

 

[Blue Bastard]

Also see if it was a v8 roadster from the factory!

 

[JGbronc]

Its a Factory V8, and it had inserts originally. Just sayin'......

 

[needabronco]

Personally I'd be thinking around $5-7,000 max. With that hack job on the striker and door jam you KNOW there's rust hiding under that paint!

But hey where I am there are Bronco's all over that place...

If a U13 is important to you, get a Marti report and do your homework. If you think the rig will get sold quickly give the guy a $100 to hold if a few days while you research. If you just want a Bronco then my assesment above is where I'd be.

 

[Blue Bastard]

Its a Factory V8, and it had inserts originally. Just sayin'......

Now that I look at the pics more you can see the insert mounting holes as well.

302 v8 according to the badges in the fender!

 

[BajaFresh75]

I see the hole in the striker too, but that doesn't mean that it came the factory with inserts. The doors are wrong and FORD didn't make a Sport Roadster, so the beltline was added.
Also, I think who ever added the doors booger welded the striker in, the striker post looks solid.

 

[JGbronc]

Now that I look at the pics more you can see the insert mounting holes as well.

302 v8 according to the badges in the fender!

It has a Marti on it. It came with a 289, and inserts (No mention of glassed and framed doors). 4:11/4:09 Limited Slip at both ends. Really not too bad of a Bronco. Tailgate isn't original either.

 

[Blue Bastard]

Pretty rare truck isn't it? 67' V8 U13

 

[JGbronc]

Pretty rare truck isn't it? 67' V8 U13

1 of 299. Pretty rare. 328 with Export 170, 71 with the standard 170.

 

[rydog1130]

I'll say that door striker weld job is priceless!!!

I think Ray Charles welded that sucker in there!

 

[fordfan]

1 of 299. Pretty rare. 328 with Export 170, 71 with the standard 170.

Every Marti that I have seen on the '67 U13 N code shows, "199 with this Engine / Transmission Codes", including this report....

 

[JGbronc]

Every Marti that I have seen on the '67 U13 N code shows, "199 with this Engine / Transmission Codes", including this report....

I stand corrected. Knew that didn't seem right

199 - 289 V8
328 - Export 170
171 - Standard 170

 

[jmangi62]

Good start to a build,trail rig or ? Not for 12k tho,more like $4500-$5000.

 

[JGbronc]

Good start to a build,trail rig or ? Not for 12k tho,more like $4500-$5000.

It'll bring more than that, especially being a U13. Even though its been modded a lot, that VIN will make someone pay more for it. Not me, but someone. It is a running driving Bronco, that is fairly solid and decent looking.

Really, the $12.5k isn't too far off base in my opinion. But my opinion don't mean much when I'm not the buyer. I'm holding out for an uncut. If I did want it, I'd offer $10k.