let's see your bronco aftermarket/replacement seats

[ricky]

going to be needing to replace my seats here soon,was wanting to see what everyone else has been using.i'd like something with more side supports..i notice some owners have been using stock seats from other cars,but i have no clue what would work without alot of floor mods,thanks in advance!

 

[vuke]

Here is a set of seats from a Mazda Protege I got at pick and pull a couple years back. They may sit a little too high if you are tall but I'm sure you could modify them to sit lower. I'm 5-10 and they're fine for me.

 

[Russ]

I used Accord seats (early 90s I think).

I'll see if I can get some pics tonight.

 

[Steve]

Here's what I put in mine last winter with the new cage:

 

[TJK74]

Mastercrafts

 

[Pokey71]

i found my seats online. a guy was selling his 98 Camaro seat.... best part is they BOLT RIGHT UP TO THE FACTORY BRACKETS!!!! only needed to drill one hole in the body .. where the drivers side latch it for the seat....

dont have a pic but i did find this on my computer

 

[Heus33]

Mine look a lot like Steve's but are cloth. They are APC. Once in awhile Pepboys will run a special for about $120 apiece. I was able to mount the sliders directly to the floor.

 

[70EB]

Procar seats. Have had them since 2000. have not sat in them much since Bronco just became roadworthy.

With these seats, you cannot be.....umm...."dimensionally challenged";D Tight fit on your fourth point of contact.

 

[lonesouth]

How about wrangler seats? Who's done it?

 

[Ohio Bronco 21]

Sorry no pictures, but I put 1970 Mustang high back seats in mine. Look like they belong.

 

[texashcane]

Not exactly great pictures, but these were $325/pair with shipping off ebay and they included the harnesses.

http://pg.photos.yahoo.com/ph/stephengwright/detail?.dir=bba7re2&.dnm=d227re2.jpg&.src=ph

http://pg.photos.yahoo.com/ph/stephengwright/detail?.dir=5393&.dnm=4231.jpg&.src=ph

 

[yak67]

PRP Racing Daily Drivers, I like em, very comfy

 

[Louie]

I put Procar Elites in the 77 I had. They were pretty comfortable for me but sat maybe an inch higher than stock even with the brackets from W/H. Then I took the rear seat down to the local upholstery guy and he recovered it to match...charging me only $100.

 

[kntr]

60/40 bench from a Ford Ranger
http://classicbroncos.com/photos/showphoto.php/photo/10169/cat/all/perpage/24/ppuser/16321
Vista rear
http://classicbroncos.com/photos/showphoto.php/photo/10164/perpage/24/ppuser/16321

Subary Legacy
http://classicbroncos.com/photos/showphoto.php/photo/9450/perpage/24/ppuser/16321

Toyota Tercel
http://classicbroncos.com/photos/showphoto.php/photo/9882/perpage/24/ppuser/16321
all in my gallery

 

[bronco-uno]

these are beard super seats that I need to mount in my truck

 

[Pa PITT]

Sorry no pictures but 1987 BroncoII ..I had a travling salesman job I put 387000 mile in them and I decided they set good ....they look really close to the Procar ones ..But about the last 20000 mile I bought a set of cloth 1988 BroncoII and after that I thought they set a fractor better than the 87's ....But with 87's setting idle I took them had them recovered in Mossy Oak Camo too match the outside ...And that's my ride ...they sure are better that the stock ones ...
I'm 5' 8'' tall and 220 lb...

 

[KANE]

Procar Rally in front, 1986 BMW 325 Bucket seats in the rear. I don't know how to insert a picture but you can see them in the gallery.

 

[sfaforester]

Here are my cheapo EBAY seats I got a few years back. They work great.

 

[bmcqueen]

Beard Sportster HighBacks

 

[bigmuddy]

aftermarket seats

bmcqueen, how much trouble do people have getting in and out of the back seat area with your seat setup? I need to eventually get some new seats or recover the stock ones and the thing that is hangin me up is the ability to get in and out of the rear area.

Ben