• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

My Stroppe Journey . . . Hidden Winch!

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I'm ready to see it again :cool:
IMG_1515.jpeg
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
OK . . . back on the hidden winch install. (I had been distracted by the new Super C!)

I got it 99% mechanically installed today. Still need to run the wiring and install the fairlead and hook. Wow! This has been a tough install! Very tight fit for the Open Road 12K winch. The RC winch may have been easier because the hidden mount was built around the RC winch. Hardest part was getting the control box in the right position to fit the space between the relocated cooler and the heat exchanger tubing. Only about a quarter inch on each side clearance. I had to relocate the control box bracket and drill new holes to reposition the box on the bracket. In the end it all fit up pretty well.

Also had to clock the clutch to point the clutch handle forward and slightly downward. That was actually pretty easy to do and it's one reason I chose the Open Road winch.

Here is the relocated control box and the clocked clutch.

IMG_8762.JPG


The winch tray in position.

IMG_8759.JPG


The winch in place.

IMG_8763.JPG


And the skid plate installed.

IMG_8764.JPG


I need to cut an access hole in the skid plate to reach the clutch handle. Not sure if I'll be able to reach the handle with my hand or if I'll need a tool/device to reach it?

I hope to finish it up tomorrow.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
I finished the winch install today. Still need to reinstall the bumper. The hidden winch kit comes with spacers to push the bumper out abut 1/2 inch. Not sure why the spacers are needed but I'm sure I'l find out when I try to bolt up the bumper! The wiring cables ran perfectly to the battery. I normally use a winch solenoid operated by a switch in the cab to turn the winch power off and on. The OpenRoad instructions just say to connect the cable directly to the battery. I may add a solenoid later.

I added some lights to to the bumper too while I have the bumper off.

I cut a 2 inch hole in the skid plate to allow access to the clutch handle. I was going to make a "key" to poke in the hole to turn the clutch handle. But turns out I can reach in with 2 fingers and turn the handle very easily. I'll look for a 2 inch plug I can cover the hole with.

IMG_8765.JPG


As you can see, I painted the skid plate a flat silver color.

Here is the the skid plate installed along with the fairlead and hook.

IMG_8766.JPG


Looking in the hole you can see the clutch handle.

IMG_8767.JPG


Here are the lights I mentioned.

IMG_8768.JPG


Tomorrow I'll get the bumper installed and maybe get the lights hooked to the upfitter switches.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
Is that a light kit or did you just pick different lights you liked?
It's a kit specific to the Bronco modular bumper. Sunpie

It has white, yellow and strobe modes if you use their harness and remote but I t think I'm just going to wire them to the upfitter switches.
 
Top