Search results

hello ok on my 75 when i let the clutch out it will hopp like the body is chattering up and down then settle out as i let clutch out body flexing or twisting ?? i can bet that someone on here has had the same thing at one point or another,cause i think its kinda common on therse with that said...

hello well here's one? ok I did the np435 swap and all seemed well but it seems like after I drive the bronc for a while and after it reaches full temp its like I lose my ability to shift like it will just grind when I try to put it in 1st or reverse at a dead stop,clutch?,sycros? don't know I...

hello where can one find a diagram of the wireing for the switch on the dash? I replaced my rear sending unit with a new one from jeffs graveyard and even with it unplugged it shows a 1/2 tank and when I plug it back in it shows full? with only like 4 gals of gas in it. I believe the problem...

hello I'am in the middle of doing this swap and i'am at the point where I need to open up the tunnel.i read on here that the body brace under the tunnel need to be cut? my question is? is it just the brace that needs to go or do I need to cut the floor in that area as well I do not have a body...

the tranny and transfer case is out and on the ground i removed the 5 bolts that are bolted to the adpter should this now come apart ? if so witch i think it should what is the trick? thanks.

hello can i use the balancer off my 302 on my 351w if so that would make life alot easyer! then i could use all my pullys off the 302. thanks

hello my bronc's a 1975 but i did a rear-end swap some time ago and i know its a large bearing (new style) rear end. so with that said would this mean it has a 31 spline axel? thanks.

Hello i would like to go to a 4.11 gear in my 75 bronco, now i know for sure that the dana 44 in the front is original and i also know that the rear end is not and i'am not sure what year it is but i do know that it is a big bearing rear end.can i just order the gear sets or do i need to...

hello in the spring of 2010 we are going to do a 351w swap in a 76 bronco and i guess we're just looking for any tips on what we might be in for i know there will be some clearance issues and what not but any input would be helpful i'am sure there has been lots of write-ups on this swap. thanks.

hello i would like to put 4.11 gears in my bronco where is a good place to order the gear sets from? thanks.

has anyone seen a 351 swap write up on how to? thanks

How well would a electric fan work with a early bronc? i'am told that you can gain some good hp by removing the mech fan but i would be worried about the electric fan taking a dump and overheating so how relieable are they? and is it worth doing? thanks.

hello i was wondering about adjusting some of the slop out of my steering box by adjusting that adjusting screw with the jam nut on to of the box i heard it was not recommended,but would you turn that screw in to take some slop out? or should i not bother? i know if you adjust too much the...

Hello i'am reaching out to the bronco gods for help:) can someone tell me the right way to adjust the track bar? i have benn reading lot and i get some conflicting info,should the suspension be hanging free of weight like on jacks on the frame or can it be done with the wheels on the ground? i...

Hello dose anyone here have an idea way my gas guage will only go to a 1/2 a tank when i know its fulli tried everything i could think of to fix it with no luck thanks for any help.dave.

Hello, i have a 75 eb and i did the chevy front disk conversion and all seems to work good,, but if i were to have to make a power stop i would be in the left lane like right now??Now i do not have a proportioning valve installed and i know that this valve is needed to control the flow between...

Hi i want to do the chevy brake conversion, is there a list or something like that that tells you from what years the spindles and stuff needed are from? thanks.

i just picked up a set of 3 1/2" lift front coils i have 4 degree c bushings in the bronc allready ok? i also picked up a set of radius arm drop down brackets, so my question is if i install the radius arm drop downs will i still need the 4 degree c bushings? any recomendations would be welcome...