Search results

There are threads doing a search but they are several years old. I have a stock replacement Ron Davis radiator that I have been running since 2005, nothing special other than aluminum. I'm starting to see temps when crawling as high as 215-220. Used to never go above 200. Explorer serp setup...

Can somebody give me the carrier bearing/race part numbers for the 9 inch standard Bronco case? Timken numbers?

Has anyone added set heaters to the procar elite seats? My seats are 15 years old but with exception to a small hole that I caused with something in my back pocket they are in great shape. The upholstery places want as much as new seats to add the heaters. Pretty risky considering the age of the...

This harness was put in 2006 and no problems. I recently removed the dash and disconnected everything while redoing the dash and paint, etc. I'm scratching my head over a short gray with thin black stripe wire that is connected to the relay, pin 86, where the relay gets activated. This wire has...

Currently in a wiring makeover and I'm wanting to have my pusher fan kick on when the temp reaches the setting but also when I stop I would like to be able to run the fan without having the key on (which is what I've been doing for years). I know this can be done with properly placed diodes...

Reworking my dash and installing IDIDIT direct fit tilt column intended for 74-77 model. I have a painless harness (Part #10108 using manual #90521 for installation) but it is an older one, 2006ish, still in great shape. My bronco is a 73 with the hazard switch on the dash which will be...

My 73 came from the factory with the Ranger package, however the side trim and grille trim was long gone and the holes filled when I bought it. It still has all the other pieces of chrome trim but it hasn't had the doors on for years and it has 1/4 guards. So all that's on it now is around the...

3 years old, works perfect, still like new. Has gear for flat tappet camshaft. I'm switching to a roller motor and since I needed to change the gear decided to upgrade to the latest version of this distributor. I checked eBay and the cheapest one I saw there was $300 plus shipping. I'll ship...

I'm sure a few responses will be the trash can...and I used to feel the same way. I had problems until I spaced it up to where air could circulate under it, never had a problem since going on 10 years. My question is whether anyone has mounted under the dash against the firewall? Doing some...

Never had any type of build thread on this Bronco. I bought it in 2004 and it has gone thru numerous upgrades over the years but has never had any body and paint work. It got a new buckaroo hood that was painted in 2007, other than that it has just been touchups from dings and bangs on the...

Can somebody confirm this is the correct flexplate for 351w and C4, tooth count is what I'm not remembering, but thinking this should be it. https://www.summitracing.com/parts/sum-g111sfi?rrec=true

In the process of reworking my stroker (395) and switching from a non roller to a roller block. Plan is/was to use the rotating assembly I have with new bearings and rings. The roller block is at the machine shop but I haven't taken them the rotating assembly as the current engine is still...

Is there a primer that comes in a spray can that can be used under single stage paint? Going to be a while before paint and need something that can be sanded and prepped without having to get it all off later, if possible. If it sounds like I don’t ‘now what I’m doing...congrats, dead on.

Planning a refresh on my 73 this spring, part of that includes reworking the dash using a new dash overlay. I'm tired of all the aluminum look (since 2005) and plan on having it all Forest Green, which is the color of the Bronco and everything else black. I have a new ididit steering column that...

Gathering pieces to rework my dash in the spring. I bought the dash overlay from WH on black Friday to save a few bucks, have it tucked away for now. Who has done the overlay, how does it attach ? do you get it in place and weld? Any tips on cutting holes and not screwing it up, other than just...

Bored.....yep Link below to 2nd thread on this bronco, it also has link back to 2012 when the first major work was done. https://classicbroncos.com/forums/showthread.php?t=279574&highlight=reviving After OCBR 2019 I decided to use some Summit bucks and some funds from selling a few parts to...

NP435 recently pulled out for auto swap. Excellent working condition. Shifter has JBfab knob. Tunnel cover and boot is included. Hand throttle cable with ends included. Flywheel, clutch, and pressure plate included. I have a gasket and seal set still in the package that will be included. PLEASE...

I have gears just pulled from one of my broncos, no idea what brand but they are in excellent shape. I need $200 plus whatever it costs to ship. Ford 9 inch = 4.11, Dana 44 = 4.09. Pics are the Dana 44 gears, I forgot to take any pics of the 9 inch before I took to storage but they are same...

Would like to have one but don't need or want it bad enough to pay new prices. If you have a used one at a very reasonable price I'm interested.

Looking at a refresh of my engine over the winter. It's 15 years old with very low mileage but I'm guessing has sucked in too much grit/dirt during that time off road. Still runs like a scalded ape but has blow by and will smoke if you lay into the throttle. I recently picked up a 351W roller...