Search results

Here are a few pics from this past Sunday, my GF and I drove up to Tellico and did some fishing, leaves are starting to change down low, up top, above ~4k, they have already dropped.

Has anyone had any experience with these new m18 Fuel Fluid-Drive impact drivers, how are they holding up compared to the older style? I'm about to purchase this set if they hold up as good as the old ones...

https://chattanooga.craigslist.org/cto/d/1975-ford-bronco/6277277670.html If anyone is interested in this Bronco contact me I know it well, was good friends with the previous owner and know the current owner also. Here is a quick list of things. 4 turn pwr steering, pwr disk brakes, Detroit...

Here is a cool old vid, not sure who it is, this may have been posted. Brings back lots of memories in the 70's. My dad and I would go to mtns, we would take my dirt bike and I would follow him in the Bronco, I had a Yamaha MX100 https://www.youtube.com/watch?v=R1JMryLOJGE

76 Bronco specs: pwr steering disc brakes twin stick t-case Detroit Tru-Trac in rear open front 2.5" WH lift TRO and riser for tracbar I'v been wanting to try these new BFG AT KO2's in the snow, havn't had the chance until this past wkend, we got some snow here so we headed up the Tellico...

Dana 35 Detroit Tru-Trac brand new, never been installed, new carrier bearings pressed on, 27 spline 3.54 an up gear, will fit Jeep Dana 35 or Ford IFS Dana 35, $325.00 plus shipping

Grant steering wheel I took off of a 74 Bronco, fit good, no problems, owner wanted diff type, all is there to install. $40.00 plus shipping SOLD

I have a Powermaster starter and Alternator for sale, both are brand new, still in the factory box, never been used. The starter is model # 9603 cheapest price I have found for this is $175, asking $115.00 plus shipping The alternator is model # 8-47101, its a 100 amp full and 70 at idle...

What is the pressure fitting size for the Thompson/Ford pwr steering pump, I think its 5/8 x 18 just wanna make sure Edit: everything I have found says its 5/8x18, if you have something diff post away. Thanks

I have a set of stainless flowmaster 40's, 2.5" inlet/outlet, very little use. $135.00, they sale for $90/piece from Summit. PM me

I am rebuilding a front Dana 44, gear swap, ball joints, all the good stuff for a friend. I am also adding a lift to the Bronco, I had the radius arm bushings laying next to the axle shafts and noticed they a looked like they may slide onto the shafts, I checked to see if they would fit into the...

I have a BC Broncos soft top for sale it has never been unwrapped from the original packaging, a friend of mine purchase it but later decided to keep the hard top, He said he will ship it for$1600 or I can bring it to the Super Celebration for $1300, the top color is called "Indian Birch" it...

Me and my GF road up to Tellico this past Sunday, she took her road bike and did a ride up Cherohala, I picked her up about 1.5 miles past Indian Boundary. I fished for couple hours before driven up to get her. Here are a few pics

I have a factory 1/2cab top for sale, the top is in great shape, gutters are solid. The PO dug out the seam sealer before he purchased it to make sure it was solid, it has never been outside since removed from the Bronco. It is not dented or rusted out, very solid, $950. Here are a few pics let...

This may have already been posted, if so ignore it, if not, enjoy http://expeditionportal.com/fords-bucking-bronco-turns-50/

Just wanted to give shout out to WH. I had a rear axle and bearing prob yesterday. I gave WH a call and Justin stayed on the phone with me for prob 20 mins getting the prob solved, now before you say that is what the vendors are suppose to do, I will say that the person I am replacing the axles...

My GF saw this field while ridding her road bike and was telling me about it, she suggested we should take the Bronco and get a few pics. So Sun we went for a drive and snapped a few shots of the 74 Ranger in this field full of Crimson Clover, they didn't turn out too bad for a phone pic.

Has anyone had any luck with actually talking to someone at Eaton. I have a Detroit Tru-trac that is giving me problems and have had no luck trying to contact them.

Not mine, body looks decent from pics, but who knows until seen in person, price a little high for no pwr ster or pwr disc brakes http://yuma.craigslist.org/cto/4824669542.html

Does anyone have the make and part #'s for the seal and O-ring that goes into/on the C4 adapter to t-case. Here is a pic of the parts http://shop.broncograveyard.com/Dana-20-Bearing-Retainer-Seal-O-Ring/productinfo/11113/ Nevermind I found it here, and just confirmed it with Advance Adapts. I...