• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

ok hard core automatic wheelers?

joe

Bronco Guru
Joined
Sep 9, 2001
Messages
1,932
what stall do u run?

thinkin bout goin with a 2200, done some research on pirate and they say it works.

any one out there got this setup.

488 with j-shift case, 36 iroks, c-4
 

Bluelimo

New Member
Joined
Jun 6, 2007
Messages
31
Loc.
Providence, UT
low stall converter

I had a converter built with a lower than stock stall speed. I have an EFI 351, C-4, 4.11, 35" MTRs, Terra low D-20. The cam is not well matched to the stall speed. It makes power 2500-5000RPM, however the engine idles smoothly down to 750 RPM. On the trail I like this converter because you can crawl all day long at 700-800 RPM without generating lots of heat in the trans. Also it is easy to drive smoothly over objects (up or down) because there is never any wind-up as you transition from idle/stop to motion. On the street it is not a fun set-up because its slow to get rolling (no drag race starts) and it does pull slightly at times when I'm stopped at a light (sometimes I've got to keep the foot on the brake a bit). ... Hope some of this is helpful.
 

cbearly

Sr. Member
Joined
Jun 20, 2005
Messages
606
Loc.
Wellington, Colorado
what stall do u run?

thinkin bout goin with a 2200, done some research on pirate and they say it works.

any one out there got this setup.

488 with j-shift case, 36 iroks, c-4

I'm close to that set up. I'm running 4.88 gears, a t-shift tcase, 35" Trexus, and a C4. I have a stock stall speed converter. I works well for the rock crawling I do. I'm not as hard core as some, but I do like to play on the rocks.

What kind of wheeling are you planning to do with it? For rock crawling I would think a 2200 stall speed is too high. For mud bogging it would probably be great with the right motor in front of it.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
2200 is a great stall. Works real good for me. I still need to keep my foot on the brakes at the stop light. The converter is going to heat up if you are all day crawling. Get a good cooler and run a lower gear to crawl all day. use your converter think of it like a drive train shock absorber. Use the slip to get over your obstacle. A locked up converter will not aid your crawling. you might as well run a standard. Even those guys slip the clutch. A torque converter is no different than a clutch, They both are built to wear out. Put a 2200 stall in it and go wear it out. A good converter can be rebuilt cheaper than a clutch.
I have a 2200 in my truck. I had set it up for an overdrive. Now with the c6 and no overdrive I wish I had a 2600 stall in it.

Bax
 

thumping

Sr. Member
Joined
Jun 6, 2003
Messages
891
Loc.
Jacksboro Tn
what stall do u run?

thinkin bout goin with a 2200, done some research on pirate and they say it works.

any one out there got this setup.

488 with j-shift case, 36 iroks, c-4

Hello Joe. I don’t really consider myself a hard core crawler although I’ve been known to try about anything. I ran a similar set up as yours but with 5:13’s on 36’s. Over the years I’ve tried different stalls and brands of converters and in the end I went back to the stock. To me, it worked as well and even better than most. Now if you’re looking to get real serious and stay with the auto, I’d look into installing a pressurized inline accumulator to prevent the transmission from getting starved for fluid when on extreme angles. This is however just my opinion. Another thing you may want to look into is getting an old plunger style solenoid off an older car that had AC. It was used to bump the RPM up when the AC compressor kicked on. You can put it on a toggle switch and adjust what RPM you want. It helps to keep your foot from bouncing up and down on the skinny pedal. Just a thought ;)
 

acbronco66

Jr. Member
Joined
Oct 2, 2006
Messages
124
Loc.
Alexander City, Al
I just installed a new rebuld c6 with a doubler 203x205 with 513 , 42 Irocks went with a stock conv. went to Wind Rock this week end and work great.
 

357Bronco

Bronco Guru
Joined
Oct 13, 2006
Messages
1,001
Loc.
New Hampsha
When choosing a converter, you look at motor, gearing, tire size and vehicle weight. If you throw that t-case in low range you throw off how the converter is going to act because you just made a major change in your gearing. As an example, the Broncos we run either in the mud bogs or sand drags are always in low range. If we want a big stall to take advantage of a tranny brake we run double the stall compared to what it would use in high range. This also makes high range useless, because the converter never locks up and slips constantly, burning up the trans. So your 2200 stall, when in low range will act more like 1100 stall when in low, yet still be street able. I wouldn't go any higher, and depending on the motor probably stock would be fine. This is the longest post I have ever typed, I think.
 

evil69

fawkin classy
Joined
Nov 7, 2003
Messages
1,950
Loc.
Athens, GA
I run a stock converter in my C-6 with 36s and 4.56s. I am not hardcore, my junk breaks too easy so I'm only half a man.
 

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
Stock, all the way. You do mainly trails with it, right? I think the stock converter will do a lot better on them and will still work with a pretty built motor. I love my motor since I took the bigger cam out and put a nice torque cam in it. It is not as fun on the street but I can crawl over obsticals a lot easier than ever before. How ever, the added torque and along with the doubler and Boggers is hard on parts.

David
 

daddyg

Bronco Parts Collector
Joined
Dec 30, 2004
Messages
2,114
Loc.
Toney,AL
I use a stock converter with 5:13s, J-shift, C-4 and mildly built 302. Works well on the trails and on the rocks..
 
OP
OP
joe

joe

Bronco Guru
Joined
Sep 9, 2001
Messages
1,932
well the 2200 stall is awesome!, on the street. first time i ever did a dry burnout, hell i could have roasted them iroks.

really sucks bad crawlin, bad idea unless you run a doubler maybe :mad:

really took alot of gas peddlin and brakin at the same time. probably would have worked out good if i just got use to it but the tranny temp went way up when i was workin it so its out and on the floor, waitin for a stock stall in the mail.

probably would have been hard on the 1/2 ton axles also.

i would have to agree its a good idea to have it lock up at the power stage in the cam but not without 1-tons and a doubler. my 2 cents
 

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
I love my motor since I put a nice warm torque cam in mine. It starts pulling almost before I hit the pedal, along with the stock stall and doubler it is a lot easier to control than my burn out monster cam I had before. It was all you wanted and more to try to hold onto and horrible to crawl with.

David
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
Ya'll keep talking this is what I'm worried about for our Hunting trip in NM this years ...Running Buddy has a 84 302... truck cam.. tr 4x4 conv... built aod built by a jeep rock climer..4.11 and p/tracs front and rear ..35's ..I sure hope this thing will climb over the mountain with an auto ...If it doesn't we'll be railigated ..to hunting the flat land like a pilgram...
 
OP
OP
joe

joe

Bronco Guru
Joined
Sep 9, 2001
Messages
1,932
Ya'll keep talking this is what I'm worried about for our Hunting trip in NM this years ...Running Buddy has a 84 302... truck cam.. tr 4x4 conv... built aod built by a jeep rock climer..4.11 and p/tracs front and rear ..35's ..I sure hope this thing will climb over the mountain with an auto ...If it doesn't we'll be railigated ..to hunting the flat land like a pilgram...

ya'all should b fine with the auto, i'd worrie bout stock axles and gearing w/35's
 

ctowery

Bronco Guru
Joined
Jan 8, 2002
Messages
1,024
Loc.
Wellington Nevada
I had Art Carr make me the lowest they could for my built 351 Lightning motor and its made a big difference all postive trail and street. Call them and give them the info on your EB and you will like the results.

Cary
 
Top