• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

1350 vs 1410 yoke??

Scrapper_MV

Sr. Member
Joined
Dec 14, 2006
Messages
960
I went out to our local spot yesterday against my better judgement. I was talked into it by my scout buddy. I was feeling sick and should have stayed home.

My friend in the Scout made a nice climb up a short steep hill that was mostly loose dirt and cobble stone. So I followed, but didn't make it on my first try. Or my second, third or even tenth. A small crowd formed to watch me attempt this spot. There were several video cameras and my scout buddy laughing while I tried. I eventually tried it with more speed and throttle, which lead to wheel hop, which led to my rear u-joint exploding. It took the yoke on my HP Dana 60 with it. I had to limp home in front wheel drive.

Have you heard what a loose drive shaft sounds like when it hits the under side of the body repeatedly? Trust me, it gets your attention!

Now of course I want to upgrade. Is the 1410 yoke & u-joint a good idea? It's bigger & stronger but does it handle as much angle as the 1350?
 
OP
OP
S

Scrapper_MV

Sr. Member
Joined
Dec 14, 2006
Messages
960
Well I got the broken u-joint out. It appears that it had been cracked near the grease fitting for some time. So I'm going to just replace it with a solid joint and call it good. Now what's the proper way to replace a Dana 60 yoke?
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
It does handle as much angle as the 1350 and then some...

http://www.pirate4x4.com/tech/billavista/PR-1410_Yoke/



U-joint series​
Maximum Angle​
Continuous rating (lb-ft)​
1310​
30​
130​
1350​
20​
210​
1410​
28-37​
250​

Good post. I didn't pay enough attention when I upgraded my junk from 1330 to 1350..that 1350 stuff is angle-limited like I would never have thunk. I'm running Wood's $$ offset joints to compensate..but still..
 

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
If this is the joint at the diff, the axle is clocked correctly, and there is an anti wrap device installed, I can't see any of those choices being a limiter for angular travel.
 

Ekrub7788

Jr. Member
Joined
Jul 31, 2007
Messages
68
Loc.
Manassas
So it sounds like that the 1350 yokes are a no go. I am looking at getting new yokes all around so they all match. What do you guys recommend? The 1330 or 1410? I think the 1410 may be out of the question.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Good post. I didn't pay enough attention when I upgraded my junk from 1330 to 1350..that 1350 stuff is angle-limited like I would never have thunk. I'm running Wood's $$ offset joints to compensate..but still..

those joints vibrate like crazy at speed. But you like that.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
If this is the joint at the diff, the axle is clocked correctly, and there is an anti wrap device installed, I can't see any of those choices being a limiter for angular travel.

X2...assuming you're running a double-cardon shaft in the rear.
 

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
I call BS on the 20 deg. angle on the 1350 joint. The angle is subject to the driveshaft components that are in play. I'm getting 38 deg. out of mine with a 2" shaft and a clearanced 205 yoke. The 1330 will not be much stronger than the 1310 that is listed but will flex more than it.

Bottom line is it sounds like bad axle wrap is the culprit. My 1350 joint in the rear has been beat on for almost 2 years and haven't had any issues with it on the rear of mine. Anybody that knows me knows I'm not easy on the skinny pedal!

David
 
OP
OP
S

Scrapper_MV

Sr. Member
Joined
Dec 14, 2006
Messages
960
Yes my shaft is a double cardon and the rear end is a Dana 60 high pinion. It was all set up correctly by Currie Enterprises. But there is no room for a traction device. But upon closer inspection we found that the u-joint had been cracked for a while. It was cracked right at the zerk fitting. So I'm having the entire driveshaft rebuilt with new spicer solid joints.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
So it sounds like that the 1350 yokes are a no go. I am looking at getting new yokes all around so they all match. What do you guys recommend? The 1330 or 1410? I think the 1410 may be out of the question.

Call this guy if you need that yolk - it's a common yolk found on Ford D60's.
http://www.northerndrivetrain.com/ - Gabe is his name, great guy.

You can get a forged if you want too-
Forged - http://www.northerndrivetrain.com/product/NDT-3-4-6211.html
Cast - http://www.northerndrivetrain.com/product/PTI-3504-60.html

As for your 1350 breaking, don't worry about it, it was axle wrap - I've been pounding the crap out of my setup and killed a D70 rear yolk on my last outing.

I'm running a 302 with a 4barrel intake and carb, C4, Atlas 3.8 and 4.11 gears on cut 37" boggers. I wheel with a VERY heavy foot with the one tons and never broken the factory 1310 ujoints in the drive shafts - I ran a 1310 to 1350 conversion joint the entire time and it didn't even break when the yolk broke.

Replace the joint with a Spicer joint (Gabe is a Spicer dealer and has TONS of stuff in stock, I was there last week and was floored with all the red and white pretty boxes) and add a traction bar and you won't have any issues.
 
Top