• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tuff Duff ride

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
My Bronco sitting on level ground. My rear shocks don't look like they have much up travel. Could that be a problem?
11613d1347741849-other-ford-sitting-my-garage-sam_7318.jpg
 

01Dudley

Sr. Member
Joined
Jul 16, 2012
Messages
974
Loc.
Knoxville
Shock up travel should be about 5". If it's way less than that then yes you could be bottoming out the shock.
 

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
Damn, just measured the shafts on those two shocks one is at 2 3/4 inch and the other is just under 3 inches. How does one go about fixing this problem?
 

01Dudley

Sr. Member
Joined
Jul 16, 2012
Messages
974
Loc.
Knoxville
Quick test! Zip a ziptie around the shaft of the shock. Slide it down to the tube. Go drive around and see how far the ziptie moves up after hitting some bumps. You will be pretty amazed and they may not be bottoming out.
 

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
If the shock is already in its last quarter of travel would that not account for a harsh ride.
Also I could imagine how this could affect the articulation of the suspension.
 

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
Here is a picture of the other side, I have almost no up-travel, this is called a long travel right?
SAM_0797_zpsfcce73da.jpg

SAM_0796_zpsa2ee98a8.jpg
 

asinor

Bronco Guru
Joined
May 13, 2011
Messages
1,396
Loc.
Tulsa, OK
That looks to short. Did you order shocks for the 5.5" lift or long travel shocks with your 3.5" lift?
What are the part numbers on your shocks?
 

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
These came in the 3.5 Kit from Duff, Wish it was as simple as having the wrong shocks installed. I have contacted Duff a couple of times by phone and they have reassured me that I have the correct part numbers and shocks on the back and said not to worry because little up-travel is needed in the rear.
Not happy to find out Duff is now saying I should have at least 5 inches. I will get the numbers off the rear shocks and post them shortly.
 

BroncoBernie

Sr. Member
Joined
Feb 6, 2005
Messages
367
duff ride

I have the 5.5 monster duff. Here are some photos, I think you have the wrong shocks. Just to let you know your truck is killer, Just saying:)
 

Attachments

  • IMG_4030.jpg
    IMG_4030.jpg
    84.6 KB · Views: 74
  • IMG_4032.jpg
    IMG_4032.jpg
    87.4 KB · Views: 57
Last edited:

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
Thanks guys these are the #'s off the shocks C151A1 8115 I had previously informed Duff with these numbers and was told that they are the correct part number for my Kit and application.
Same part number on all 8 shocks, the fronts are extended 7 1/2 inches which is about half way as the body of the shock is about 14 inches.
11612d1347741768-other-ford-sitting-my-garage-sam_7309.jpg
 

01Dudley

Sr. Member
Joined
Jul 16, 2012
Messages
974
Loc.
Knoxville
http://www.dufftuff.com/Stage_1_Rear_Shock_Mounts_1966_77_Bronco_p/5215.htm

Here is a picture of the Stage 1 kit we ran on HiHo Silver for years. Notice the dirt on the shaft compared to the clean part of the shaft. Looks about the same as your set up. Can you test the up travel by putting a ZipTie on the shaft to help us confirm weither or not the shock is bottoming out? HiHo Silver now has the Stage 2 on the rear and that is why I posted the 5" up travel yesterday. We have no problem changing shocks w/you but the major question is are you bottoming them out? Cause if you are not bottoming them out then the shock is not the issue. The 8115 fully extended is 26.25" fully and collapsed is 16". The next shorter shock, which also happens to be our shortest shock w/eyelet on both ends, is fully extended is 24.25" and collapsed is 15". What is your measurement right now eyelet to eyelet? Should be around 20"? Let us know what you get after the ZipTie test and we will proceed with trying to figure out the issue. We just don't want to throw parts at it and not solve the rough riding problem. Have you tried to remove a shock and see if the ride improves?
 

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
Thanks Dudley You can see pictures of the Bronco if you click on my Garage under my username and avatar.
I love the whole Duff package with 8 shocks and would hate to remove 2 of them. My biggest concern is the short amount of up-travel I have remaining, the rear Duff bump-stop is about 4 1/8 inch from contact so my thinking is the shocks would be damaged before the bump ever comes into play.
I only have debugging road miles on the Bronco so I don't think it has ever bottomed out on the street but I am assuming it would off-road.
One thought I have is maybe using the brackets for the 2 inch body lift, I assume I would have to notch out part of the lip on the inner wheel well (as my body-mounts measure just under 1 inch) which would give me an extra 2 inches. Has anyone tried this, I think I remember seeing pictures?
 

br0nc0xrapt0r

Loves pickles
Joined
Sep 28, 2007
Messages
5,439
Thanks Dudley You can see pictures of the Bronco if you click on my Garage under my username and avatar.
I love the whole Duff package with 8 shocks and would hate to remove 2 of them. My biggest concern is the short amount of up-travel I have remaining, the rear Duff bump-stop is about 4 1/8 inch from contact so my thinking is the shocks would be damaged before the bump ever comes into play.
I only have debugging road miles on the Bronco so I don't think it has ever bottomed out on the street but I am assuming it would off-road.
One thought I have is maybe using the brackets for the 2 inch body lift, I assume I would have to notch out part of the lip on the inner wheel well which would give me an extra 2 inches. Has anyone tried this, I think I remember seeing pictures?

I want you to think about geometries of your rear suspension for a sec, while the shocks may be a bit short in the up travel dept think about your swing shackes. The shocks are at about a 45 degree angle from the axle towards the front of the bronco. If the axle traveled in a perfect up down motion this still gives you more travel than meets the eye. See the distance that the shocks travel at the 45* angle is about half if they were verticle over the axle tube. Now take into account your shackles. They are in the rear of the spring pack and they allow the spring to reduce arch along it's length. As we take this U arch and flatten it, it gets longer for lack of a better term. The shackle lets it expand it's length toward the rear so as your axle moves up in travel it also goes back towards the rear in the direction that the shackle allows it to. So not only are the shocks at a 45 from the tube but as the axle moves up towards the shocks it's going backwars and away.

The same thing could be said for down travel. The axle tube moves down away from the shocks but the shackle forces it towards or forward to the shocks.

This is how your Duff system works, I on the other hand made my own inboard double shear hoop that mounts in a similar manner. I have 10.5 inch travel bilstien 7100 smoothies and about 4.5 inches of shaft showing at ride hieght on a 5.5 inch deaver pack. I have never maxed out these shock crawling or jumping.

Let it also be known that the decreased use of shock travel in this setup is also a need for better shocks in this application. The Duff shocks are a fine shock but lack some of the high pressure that my bilstiens have "220 psi of nitrogen" Nothing wron with this but it's why Duff gave you two. This is one of the rare circumstances that I would condone running a two shock setup unless you were to spend some serious money on shocks.

Hope this helps.

Nick
 

01Dudley

Sr. Member
Joined
Jul 16, 2012
Messages
974
Loc.
Knoxville
Trimming required

You can most certainly do that and trim the inner wheel well. I agree you will never hit your bump stop(unless something is severely wrong). I also agree with what br0nc0xrapt0r says and yes the Bilsten are charged differently and if I were running Bilstens you would only run 2 on the rear, but that doesn't mean it will be any better ride that our 4 shock set up. From the start, our trouble isn't that the shocks are bottoming out, the problem has been rough ride. Without checking to see if the shocks are bottoming out, regardless if they are inboard, outboard, Duff, or Bilsten, we are just chasing the problem in circles. Yes the extended travel 2" body lift brackets and possibly even the 8110 shock will improve the offroad capability, but it still may not ride any better. Lets solve that issue first and who knows the other may solve it's self.



Thanks Dudley You can see pictures of the Bronco if you click on my Garage under my username and avatar.
I love the whole Duff package with 8 shocks and would hate to remove 2 of them. My biggest concern is the short amount of up-travel I have remaining, the rear Duff bump-stop is about 4 1/8 inch from contact so my thinking is the shocks would be damaged before the bump ever comes into play.
I only have debugging road miles on the Bronco so I don't think it has ever bottomed out on the street but I am assuming it would off-road.
One thought I have is maybe using the brackets for the 2 inch body lift, I assume I would have to notch out part of the lip on the inner wheel well (as my body-mounts measure just under 1 inch) which would give me an extra 2 inches. Has anyone tried this, I think I remember seeing pictures?
 

BRONCOBERT

Sr. Member
Joined
Sep 2, 2012
Messages
731
Just wondering do these shocks become progressively stiffer as they compress? I know some shocks do to help with the last 1/4 of travel to help prevent bottoming out.
Also would the Brackets for the 2" body-lift bolt up in the same spot my current one does or would I have to drill new holes in the frame, also the mounts that are welded on the 9" rear end could they be used in the current position or would new ones need to be re-positioned and welded on?
 

01Dudley

Sr. Member
Joined
Jul 16, 2012
Messages
974
Loc.
Knoxville
Oh and our first run of Billet pedals exclusively for us from LOKAR will arrive one day next week! Kits include all pedals and the dimmer cover. No drilling required / bolt on and available in brushed or anodized black. Just food for thought!
625throttlepadrubber_zps640feeef.jpg

clutchandbrake_zps7d5d5265.jpg
 

br0nc0xrapt0r

Loves pickles
Joined
Sep 28, 2007
Messages
5,439
Just a thought what tire pressure are you running? I know that letting air out is not always the best answer but I only run 20 psi on the road/highway and 8 psi offroad.
 

01Dudley

Sr. Member
Joined
Jul 16, 2012
Messages
974
Loc.
Knoxville
same mounting positions!

Our shock does not get stiffer the closer to bottoming out it gets. I just went and compressed one by hand. The mounts are the same for the Stage 2 as they are for the Stage 1. Just need to trim the body.




Just wondering do these shocks become progressively stiffer as they compress? I know some shocks do to help with the last 1/4 of travel to help prevent bottoming out.
Also would the Brackets for the 2" body-lift bolt up in the same spot my current one does or would I have to drill new holes in the frame, also the mounts that are welded on the 9" rear end could they be used in the current position or would new ones need to be re-positioned and welded on?
 
Top