• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Mike's 77

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
Also know as "I don't have a clue what I'm doing" or "What have I gotten into?"

So back in December I picked up a 77 with 3 on the tree. It is rough and I think I paid too much but it has good bones and I was tired of looking. I had gone hundreds of miles looking at several different Broncos and finally decided I just needed to latch on to one and deal with it.

Here it is.

0GnBTXJ.jpg


qhesYjW.jpg


She runs good and shifts good but is all over the road. Going to put new bushings in the front for starters.

The body is not very nice at all. It looks good, but someone has definitely put some hillbilly engineering into getting it road worthy. It is fine for general driving around as is but will need lots of work or a complete replacement. Since I live in the lower rust belt, I am considering fiberglass so I enjoy year round driving.
 
OP
OP
msmith

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
Current situation.

I got the brakes off, spindles off, and the steering knuckles. Found a couple of bad ball joints. I decided to sand blast and paint everything while I have it apart and waiting on ball joints. I figured I might as well replace all of the seals and repack the bearings while I am at it but...I'm not sure exactly what I have.

I don't know what front end I have. It has disc brakes but it also has T steering. The brakes look like factory 76-77 but the knuckles aren't. My tie rods are 48" c-c. So now I'm not sure what seals to get.

I also figured that while I have the axle out, I might as well regear while it is easier. I also think I am going to replace the suspension with Duff's while I have everything apart. My wife is trying to be understanding.

ofiaLW4.jpg

p2DIn28.jpg

7ymfLkn.jpg

abxfv99.jpg

YVopTzX.jpg
 

Kbpony

Sr. Member
Joined
Jan 31, 2012
Messages
386
Maybe the “Y” steering was replaced with a “T” conversion? The calipers look like original equipment. I think the truck looks pretty good, I’d drive it a while as is before tearing into it too far. Tighten it up and have fun! By the way, if your wife is trying to be understanding now, you might want to make getting into her good graces a priority, you’ll need her support down the road.
 
OP
OP
msmith

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
Maybe the “Y” steering was replaced with a “T” conversion? The calipers look like original equipment. I think the truck looks pretty good, I’d drive it a while as is before tearing into it too far. Tighten it up and have fun! By the way, if your wife is trying to be understanding now, you might want to make getting into her good graces a priority, you’ll need her support down the road.

That's what I was thinking but I'm not sure what the Y conversion is. Just steering knuckles?

It does look pretty good and is a pretty decent driver. I already have 4.56s lined up and am going to pull the body and go over the frame and treat it with the KBS products after I get it re bushed and the axle back in. My buddy, who is a pretty decent shade tree body guy, is going to evaluate the sheet metal and we'll come up with a plan accordingly.

My wife is great and I was kidding about her trying to be understanding. She is very supportive. She has a 2021 of her own on order.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
You think that's rough? Maybe if this was 1980. You've got a great starting place for a great restoration.
 

stout22

Contributor
Bronco Guru
Joined
Dec 13, 2006
Messages
3,022
Loc.
Athens, AL
I'm not sure if that is a stock 76-77 bronco dana 44. I don't see the factory brackets for the sway bar. It could be the angle of the picture?
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
Y is not a conversion. "Inverted Y" steering is what came stock on 76's and 77's. Many serious off-roaders ditch the Y steering for heim-joint set ups in the earlier configuration. Y is good for on road but not for rock crawling.

Looks like a great start and a pretty solid Bronco. Keep the pics coming!
 
OP
OP
msmith

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
Y is not a conversion. "Inverted Y" steering is what came stock on 76's and 77's. Many serious off-roaders ditch the Y steering for heim-joint set ups in the earlier configuration. Y is good for on road but not for rock crawling.

Looks like a great start and a pretty solid Bronco. Keep the pics coming!

Thanks. It's going to be a fun project. I hope to do a little and drive a little, gradually making upgrades.

What I meant by Y conversion is converting from Y to T. I'm not sure if my axle is a 77 that someone has changed from Y to T or if the axle has been swapped out. Either way, I'm fine with it as I would have eventually changed to T anyway.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
Thanks. It's going to be a fun project. I hope to do a little and drive a little, gradually making upgrades.

What I meant by Y conversion is converting from Y to T. I'm not sure if my axle is a 77 that someone has changed from Y to T or if the axle has been swapped out. Either way, I'm fine with it as I would have eventually changed to T anyway.

Gotcha! I guess I read that wrong.
 

frenchy

Contributor
Bronco Guru
Joined
Nov 29, 2005
Messages
1,043
What do your steering knuckles look like? Original 76 77 knuckles have a high steering arm to them. 78 79 steering knuckles have a lower steering arm on them. Someone changed to a t steering setup on the stock 76 77 axle. And or someone robbed the 76 77 dana 44 out of it and then installed a drum brake dana 44 and then converted it to disc using 78 79 steering knuckles and stock ford disc brake components and then added the 78 79 t steering.
 
OP
OP
msmith

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
What do your steering knuckles look like? Original 76 77 knuckles have a high steering arm to them. 78 79 steering knuckles have a lower steering arm on them. Someone changed to a t steering setup on the stock 76 77 axle. And or someone robbed the 76 77 dana 44 out of it and then installed a drum brake dana 44 and then converted it to disc using 78 79 steering knuckles and stock ford disc brake components and then added the 78 79 t steering.

Here is the passenger side steering knuckle.

pn6qzSV.jpg
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Ford only welded the sway bar bracket on the pass side and those often get knocked off. The driver's side bracket was a separate part held on by the U bolt. The inverted Y is an excellent system that handles far better than the T system. It eliminates the dangerous bump steer issue. Rock crawling is a good way to destroy a beautiful Bronco and nothing else. Buy a rusty wreck or make a tube frame for that. Off roading meaning driving where there is no road rarely if ever involves rock crawling.
 

WheelHorse

Bronco Guru
Joined
Nov 22, 2004
Messages
2,511
Just enjoy having fun with it.

I would agree that if you are adamant about year round driving, go for a messy bar chain oil/wax spray coating underneath and soaking inside door pillars what-have-you if you stay steel.

With a fiber glass body, you'll have to factor in that crash protection would not be the same as a steel body. Steel Broncos are pretty tough for their time.
 
OP
OP
msmith

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
OK, it took a while to get my regear done but we're finally making a little more progress.

Got the Dana 44 back, wire brushed and sealed.

nB1po6A.jpg

IWa8hOD.jpg
 
OP
OP
msmith

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
Got the James Duff 2.5 inch lift on, painted calipers, new ball joints, spindle bearings and seals, new wheel bearings and seals. Painted the hubs, calipers, and steering knuckles and new dust covers for the discs.

I didn't feel comfortable with the threads on the radius arms being cross threaded so I went ahead and got forgiveness from the financial committee for ordering the Duff's T Rex arms. Man it took a lot of tries and different tightening sequences to finally get the arms almost parallel. I got it to where a 1/16th drill bit wouldn't roll under the side that didn't touch the floor.

Pv1rId7.jpg


7e5mLpH.jpg


New brake lines and adjustable track bar (that still needs tweaking), then start on the rear.

RYh86dW.jpg



The tie rod ends aren't hateful but don't seem to have a lot of life left, so I figured I'd save up some of my lunch money and go with heim steering sometime this fall or spring.
 
OP
OP
msmith

msmith

Contributor
Full Member
Joined
Feb 24, 2019
Messages
247
Finally got it on the road for a couple of days. Now back in the garage for a Delphie steering box, Saginaw pump, and a radiator.

fedf19a1452ea59e0a736a0ab54e7ef9.jpg

364ef5e428fa3361351d8a7c65b323e9.jpg



Sent from my iPhone using Tapatalk
 
Top