• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

EFI Throttle Cable

coachbarnes

Bronco Guru
Joined
Aug 3, 2001
Messages
2,717
Loc.
Franktown/Breck, CO
I've exhausted my search capabilities on here and youtube, so need a little help.

I'm running a Foxbody EFI and just swapped out the throttle body. I must have dicked up something when reinstalling the throttle cable and the cable snapped at the pedal as soon as I pressed it. I'm got the BC Broncos bracket (passenger side) and just received a new cable. I'm looking for pics/video of how to install the cable from the pedal forward and adjust it property. Any help is appreciated!


Sent from my iPad using Tapatalk
 

tasker

Contributor
all knowing of nothing
Joined
Jun 2, 2006
Messages
21,708
Loc.
NH
This help any?
EFI.jpg
 

Attachments

  • EFI2.jpg
    EFI2.jpg
    224.1 KB · Views: 284
OP
OP
coachbarnes

coachbarnes

Bronco Guru
Joined
Aug 3, 2001
Messages
2,717
Loc.
Franktown/Breck, CO

thanks -- is that a stock Foxbody 58mm TB? also, I assume you are running standard trans since no kickdown cable?

When adjusting cable to fit, I guess you just determine distance of travel to get butterfly into full open position (about 2.75" in my case) then cut the cable at the TB connector? Are you getting full throttle with this bracket & cable?


Sent from my iPad using Tapatalk
 
Last edited:

tasker

Contributor
all knowing of nothing
Joined
Jun 2, 2006
Messages
21,708
Loc.
NH
stock Mustang T/body, FULL throttle, did cut cable at t/body end....4R70W
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
I am running the BC EFI linkage and a C4 with the kickdown on 2 broncos for years. The cable is very thin and has popped out of the ends a couple of times while driving. The double set screw is not very strong. I drilled a deeper hold in the center of the gas pedal connector so I could get the cable deeper. I also used a countersink bit on the small hole opening so I could get the wires in with a small shrink wrap tubing over the cable. It can be a nightmare to get all the wires in the small holes.
 
OP
OP
coachbarnes

coachbarnes

Bronco Guru
Joined
Aug 3, 2001
Messages
2,717
Loc.
Franktown/Breck, CO
I am running the BC EFI linkage and a C4 with the kickdown on 2 broncos for years. The cable is very thin and has popped out of the ends a couple of times while driving. The double set screw is not very strong. I drilled a deeper hold in the center of the gas pedal connector so I could get the cable deeper. I also used a countersink bit on the small hole opening so I could get the wires in with a small shrink wrap tubing over the cable. It can be a nightmare to get all the wires in the small holes.

Thanks -- I've got it all installed but can't get full throttle. I honestly think that after several years of never having my Bronco run "right" with this EFI, I'm trashing it and going back to a simple little Holly TA!!


Sent from my iPad using Tapatalk
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
You may need to move the ball stud further out by drilling another hole. I have full throttle on both setups. There is a tiny bit of final travel left but it will not open the throttle body any further but will prevent me from pulling the cable out.
I can post pictures if it would help. Just let me know.
 
OP
OP
coachbarnes

coachbarnes

Bronco Guru
Joined
Aug 3, 2001
Messages
2,717
Loc.
Franktown/Breck, CO
You may need to move the ball stud further out by drilling another hole. I have full throttle on both setups. There is a tiny bit of final travel left but it will not open the throttle body any further but will prevent me from pulling the cable out.
I can post pictures if it would help. Just let me know.
The newer BC adapter has another hole that provides more travel (about 3.5") but I had to use the closer one because my pedal only give me about 3" of travel.
 

bronco italiano

Bronco Guru
Joined
Feb 1, 2004
Messages
2,595
That is so odd.
But I never checked for WOT as my RPM limiter is at 5200rpm.
Your setup looks exactly as mine.
I will post a pic
 

Postalpal

Contributor
Jr. Member
Joined
Jan 11, 2017
Messages
81
Loc.
Thornton
I've exhausted my search capabilities on here and youtube, so need a little help.

I'm running a Foxbody EFI and just swapped out the throttle body. I must have dicked up something when reinstalling the throttle cable and the cable snapped at the pedal as soon as I pressed it. I'm got the BC Broncos bracket (passenger side) and just received a new cable. I'm looking for pics/video of how to install the cable from the pedal forward and adjust it property. Any help is appreciated!


Sent from my iPad using Tapatalk
Agree. I kinda need to see exactly how it properly goes through the firewall & how to adjust it
 

Postalpal

Contributor
Jr. Member
Joined
Jan 11, 2017
Messages
81
Loc.
Thornton
You may need to move the ball stud further out by drilling another hole. I have full throttle on both setups. There is a tiny bit of final travel left but it will not open the throttle body any further but will prevent me from pulling the cable out.
I can post pictures if it would help. Just let me know.
I’m curious to see, I have the same cable it’s all installed except for the small connector on the pedal
I’m baffled because 1) it’s very hard to get the cable through the hole & when you do it’s barely in the connector when you tighten the Allen head. Seems like this cable would be better if it went through the whole connector & then you you have adjustment room As it is now you cut the cable & if you went too short your screwed

Once I have the cable through the firewall coming out by the pedal & the connector on the pedal. What is the proper way to adjust / connect this set up ? Thank you
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
I drilled the hole deeper and used heat shrink tubing over the cable to maintain the wires together. I suppose you could just drill all the way and no cut the cable.
 
Top