• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Engine Builder in SoCal

bronco italiano

Bronco Guru
Joined
Feb 1, 2004
Messages
2,595
If your willing to travel to NorCal, my engine builder is B & R machine in Stockton. He just did Jim Creels 351w for his wife's bronco. He has been a machinist for over 50 Years mainly Ford/Chevy/Pontiac/Buick/Olds. Old school that knows what he is doing. Very reasonable as most of the money is in parts. His machine work is awesome. Only downside is he is a three person show so you have to wait in line, but well worth the wait.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I always felt like the advantage of a three man show is, pretty much every hand knows what the other hand is doing. And if not, one can ask the other pretty easily!

One thing I forgot to mention Jeremy, is the clutch bracket hole. If yours is a manual transmission, the newer blocks don’t have that hole.
Not an insurmountable issue either, as there are not only parts available to get the job done, but you can also drill and tap your own hole if you need to. At least on some of the blocks.

And Molesworth, what part of the area are you in specifically? I would say just keep watching this thread and see what other suggestions come up.
 

Molesworth1991

New Member
Joined
Feb 3, 2025
Messages
20
I always felt like the advantage of a three man show is, pretty much every hand knows what the other hand is doing. And if not, one can ask the other pretty easily!

One thing I forgot to mention Jeremy, is the clutch bracket hole. If yours is a manual transmission, the newer blocks don’t have that hole.
Not an insurmountable issue either, as there are not only parts available to get the job done, but you can also drill and tap your own hole if you need to. At least on some of the blocks.

And Molesworth, what part of the area are you in specifically? I would say just keep watching this thread and see what other suggestions come up.
Appreciate the help. I just moved to Venice beach, I bought a fairly done up 351w off a guy it had the following

Redecked with .040 bore at 13:1 compression
Aluminium performer heads
Chromoly comp cams push rods, comp cams ARP studs
Kieth black pistons
Trick flow double roller timing chain -

List goes on…. I was trying to tune engine the other day and noticed zero vacuum, fairly tight to turn over, and metal on dip stick. Put a camera down the distributor port and the cam shaft is completely ruined. I was so angry after spending 8months doing a full ground up build on my 74 to install a trashed engine.

Hoping I can reuse some of these parts and the internals less the cam etc are good to re use. I hear TG do great work.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
JGM built my yet to be installed 408. Seems to specialize in Fords from what I saw in the delivery area. Recommended.

661.257.0101
28130 Ave Crocker, Santa Clarita, CA 91355
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I was trying to tune engine the other day and noticed zero vacuum, fairly tight to turn over, and metal on dip stick. Put a camera down the distributor port and the cam shaft is completely ruined.
Wow! Extremely frustrating I can imagine!
Sorry to hear that. I would think most of the stuff is reusable, but you won’t know till you tear it apart.
What exactly was wrong with the cam? Was it the gear chewed up from a mismatched distributor gear perhaps? Or are the cam lobes wiped out?
Guessing “just” the gear, because you looked through the distributor bore.
Is it a flat tappet cam, or roller?
 
OP
OP
J

jeremywatco

Full Member
Joined
Feb 8, 2019
Messages
305
Loc.
San Diego, CA
I always felt like the advantage of a three man show is, pretty much every hand knows what the other hand is doing. And if not, one can ask the other pretty easily!

One thing I forgot to mention Jeremy, is the clutch bracket hole. If yours is a manual transmission, the newer blocks don’t have that hole.
Not an insurmountable issue either, as there are not only parts available to get the job done, but you can also drill and tap your own hole if you need to. At least on some of the blocks.

And Molesworth, what part of the area are you in specifically? I would say just keep watching this thread and see what other suggestions come up.
Thanks! Mine has a C4 and Dana 20. Both are out for rebuilds as well right now.

I ended up buying that ATK engine should be here in a week or two. I think I will eat the core deposit and keep my core. Who knows.. maybe some day I will find a reasonable local builder and rebuilt it for this or another project.

Once it arrives I'll figure out what is needed to mount it up. For sure the oil pan.. may need to move over my existing pertronix dizzy as well.. the photos look like the HEI dizzy it comes with is pretty tall and will hit my hood. Pretty sure I can mount my C4 right to the 50oz flexplate it comes with.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yes. As long as it’s 164T flywheel/flex plate it should mount up just fine and the starter should work just fine.
Wouldn’t hurt to count the teeth anyway! :)

Is it a roller cam engine? If so, make sure that whatever distributor you use as a compatible gear. Yes, HEI distributors are massive and often get in the way.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Sounds good. Let’s become an important aspect of engine building for many years.
Did you say this is a new engine that you’re firing up? You’re familiar with initial cam break-in procedures? Or does ATK do the cam break in for you?
 
OP
OP
J

jeremywatco

Full Member
Joined
Feb 8, 2019
Messages
305
Loc.
San Diego, CA
Its a crate engine from ATK. I'm supposedly getting instructions with break-in info.. but any info you have would be great
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I am interested to hear what ATK says, with regard to break-in. But we can definitely run it down here as well.
Post up what the instructions have to say when you get the engine.
 

StnePny

Contributor
Bronco Guru
Joined
Dec 28, 2008
Messages
1,258
Loc.
Santa Monica, Ca.
Appreciate the help. I just moved to Venice beach, I bought a fairly done up 351w off a guy it had the following

Redecked with .040 bore at 13:1 compression
Aluminium performer heads
Chromoly comp cams push rods, comp cams ARP studs
Kieth black pistons
Trick flow double roller timing chain -

List goes on…. I was trying to tune engine the other day and noticed zero vacuum, fairly tight to turn over, and metal on dip stick. Put a camera down the distributor port and the cam shaft is completely ruined. I was so angry after spending 8months doing a full ground up build on my 74 to install a trashed engine.

Hoping I can reuse some of these parts and the internals less the cam etc are good to re use. I hear TG do great work.
Howdy, neighbor....I'm in Santa Monica
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Just noticed the 13:1 CR?!?! That's starting to be methanol fuel territory. Unless tightly controlled EFI I'd want no more than about 9.5:1 for pump fuel. Even with tightly controlled EFI you shouldn't go much more, maybe 10.5-11:1 at most. Not for pump fuel anyway.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Its a flat tappet engine.. so should be ok
Ok for using the standard distributor gear. Not ok for just starting and driving it however.
And as you will likely hear, modern flat-tappet cams and modern oils are not what they once were. Hence doubling down on the advice to use a specialized break-in oil, and/or a specialized break-in additive.
And for me, I keep using the specified oils for older flat-tappet engines. Many will say that once the cam is broken in, you can use any kind of oil you want after that. That might be true, or it might not. All I know is that I hear of more and more high-mileage engines that are wiping out their cams than I remember from years passed. So I'm sticking with high-zinc oils for general use. Even after the break-in procedure is done.
And speaking of which...

My personal version of the procedure will follow. I've kept to my old version as instructed by cam manufacturers back in the sixties, versus the modified versions that have come along in the meantime. Because I'm patient and have nothing better to do when I'm breaking in the cam, than to just break in the cam! I don't need to rush it.
So mine is the following:

1. Get everything and everyone ready for first startup. Verify as much as you can, so that the engine will fire right up instantly. Or as instantly as you can make it. Cranking the engine on a starter for longer, equals very bad. A quick start is very good.
The startup is why engine builders apply specialized lubricants to the camshaft during the build.
Prep should include putting fuel into the carburetor float bowls, if running carbureted. Or pumped up if using EFI.
If you're installing the intake manifold, verify the builder used "cam grease" or moly-lube or whatever they're calling the paste, or very sticky oil substance that is applied to the lobes prior to assembly. Then pour your chosen engine oil down the valley and through the return holes to get some more in the area of the camshaft.
1a. Prime the oil pump with a priming too. NOT by cranking the engine if you can avoid it.
1b. The previous steps may already have been done. But I mention them just in case, because you need to be ready to run.
1c. It pays to have helpers with eyes. If not, you'll be very busy for awhile! Pre-connect your timing light so you can verify what's going on.
1d. Needless to say, you absolutely must have all your gauges connected.
2. Fire the engine up! And immediately rev it to between 2500 and 3000 rpm and hold it there. This may very well be the hardest part to do, for any first-timer. But do it anyway!
2a. Remember, NEVER let it idle down. No matter what you need to do, do not idle the engine. Best to stop the engine first, fix the issue, then fire it back up and run it up to the specified rpm.
3. Keep it at that range, but after the first minute or three, you can vary the rpm slightly up and down, but don't go below 2,000 for more than a few seconds, and stay above 2500 for as long as you can.
4. This period of adjustment, so to speak, should last for a full 30 minutes total. So make sure that the gas is in the tank and getting to the engine.
It does not have to be all at once, but that is better. If the engine gets too hot, you can turn it off to let it cool down. But don't idle it.
If you see a gas leak, shut it down to fix it. But don't let it idle.
If you see no oil pressure, shut it down (that should be obvious!). But don't let it idle.
Fix any issues, then fire it back up and bring it back to 2500-3000 immediately.
Seeing a pattern here?

This whole procedure revolves around not letting the engine below 2,000 rpm until at least 20 minutes of run-time have elapsed. I prefer 30 minutes, as I mentioned. But modern instructions often say 15 to 20 minutes and I've seen as low as 1500 rpm. And modern cams are often ruined in today's world. Is it due to the shorter duration, or lower rpm of the break-in? Or is it due to crappy materials? Or is it due to poor assembly? We may never know.
But I'm sticking with with 2500 and up, and 30 full minutes in my builds. So far so good, but I have not done one recently either. So I'm doing it my way, but also crossing my fingers!
Of course, I crossed my fingers every time (because I knew the consequences) since the sixties! But back then, I think crossing fingers yielded better results as well. :cool: :D

Good luck. Hopefully others here will chime in with recommendations, modifications, or whatever advice they can put forth.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I thought I'd mention it here, in case it wasn't obvious while buried in all the previous words.
Cranking the starter for an extended period without the engine firing is BAD.
Letting the engine idle while you "tune it up" or "make adjustments" is BAD.

It's all about lubricating the cam lobes and base of the lifters.
Those areas are lubed at least primarily by "splash lubing" from oil kicked up by the rotating bits, and spewing out of the sides of the cam bearings, and from oil falling down from above in the lifter gallery/galley/valley. The more oil that is pumped through the heads and rocker areas, the more falls down on to the cam.
I'm not sure if they get lubed from any other source, but this is precisely why you kick up the rpm to at least 2,500 for the initial run-in/break-in procedure.
The higher rpm probably also has a dynamic effect on the spot pressures seen between the lifter base and the cam lobes.
Dancing over, vs scraping by, might be an apt description for that?

Dunno. All I know is I prefer to play it safe in all aspects and run 'er up at first start up!

Paul
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
When I worked in the engine machine shop we offered an engine break-in service on the dyno. We didn't put a load on the engines, but the dyno offered an easy way to hook up and monitor everything.

The oil splash inside an engine varies with RPM. As result we never let an engine during break-in linger for long at one RPM. A couple mins at 2300, then move it 3100 for a few, then move it to 2800, then move it to......
You get the idea.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thanks. I didn't put enough emphasis on that aspect in my reply above.
Glad you brought up that important point.

Paul
 
Top