• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

My Stroppe Journey . . . Hidden Winch!

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
If you find a winch that does not have remote that you like, I’ve been really happy with this Remote from the jungle I have few of them, the work really well.

I really should buy a new winch or 2, but keeping my pile of old ones going hasn’t been difficult enough lol. I only have one still using a solenoid pack, the rest are all using an Albright contractor, had good luck with inexpensive jungle ones.
 

BluebroncoNC

Bronco Guru
Joined
Jul 30, 2007
Messages
1,768
Loc.
Asheville, NC
I got all the prep work done to make room for installing a hidden winch. Not for the faint of heart! For the 2.7 L it takes a lot of moving components around, (as shown above) cutting the frame horns off, and cutting a number of coolant hoses to shorten them. All this to have a hidden winch so that I don't mess up the looks of the front end of a Stroppe! It would have been much easier to install a bumper mounted winch tray like I had on my '22 Badlands.

Install note: The instructions call for removal of the intercooler down pipe. I called Rough Country to ask why this was needed. Tech person said probably to make access easier to do the component relocations. He said I could try to do it without removing the downpipe and it would then be obvious of why it was needed. I found no issue with leaving the downpipe in place. So no need to remove the downpipe!

That said the mods went well and I checked for leaks - none.

Aux pump relocated and hose marked for cutting.

View attachment 966362

Bracket relocation.

View attachment 966363

Cutting one of the lines.

View attachment 966364

RC bracket relocating the cooler. This shows the area opened up to install a winch.

View attachment 966365

Relocated pump with the hoses shortened and installed.

View attachment 966366

Next is selecting a winch and installing it! Issues to still be resolved: 1. How to access the clutch lever; and 2. Will I need to relocate the control box on the winch I select? There have been various solutions for both of these issues but I need to research more for the best solutions. One thing I want in a winch is a cordless remote.
Pm'n ya
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
I may end up with the RC winch but still looking at others. I've seen posts where 12,000 lb winches have been successfully installed but it's a very tight fit. I'm looking at 9,500 or 10,000 lb winches. I need to test mount the tray and actually measure the space,
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
Decided to go with the OpenRoad 12K winch.

  • Same size dimensions as their 10K
  • Comes with 2 wireless remotes
  • Synthetic rope
  • Nice hook
  • Moveable control box
  • Clutch housing is rotatable to different positions for the clutch handle
Having the ability to reposition the clutch handle is a big plus so I have some options to be able to access the handle. Winch tray is 24 +- inches and the winch is about 21 inches wide. Height without the control box is 7 1/2 inches. Should fit fine.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
There was a slight vibration sound when driving it after the work to make room for the winch. I pulled the skid plate back off and a couple of the lines (brake line and one of the transmission fluid lines) were rubbing on the new bracket. I bent them slightly to give them some space and the sound has gone away!

Winch has shipped - should get it this week. But I may not be able to install it until after Super Cel which is after Labor Day. Then we're off on an RV trip for 2 weeks. Winch install may have to wait until October!
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
The OpenRoad winch arrived today. Their promotion included a "free" 30 foot kinetic rope and 2 soft shackles in a nice carry bag.

IMG_8170.JPG


IMG_8171.JPG


I might even open the box tomorrow!
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Nice!

As I am seriously considering purchasing a new winch, one thing I would like to know is how difficult the free spool to pull? That is my one complaint of all of my existing winches, the high effort the free spool to pull line out.

PS; I understand it may be a while before you have an answer lol.
 

ssray

Contributor
Sr. Member
Joined
Apr 19, 2010
Messages
921
Loc.
South Central NE
Nice!

As I am seriously considering purchasing a new winch, one thing I would like to know is how difficult the free spool to pull? That is my one complaint of all of my existing winches, the high effort the free spool to pull line out.

PS; I understand it may be a while before you have an answer lol.
How about a small gearmotor with a capstan, spring loaded roller microswitch control. 2 or 3 wraps around the capstan, under the switch roller, put a little tension on the line and off you go. Let off and the motor stops. 😉😂
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
The biggest issue I see in this hidden winch set up is the clutch lever. It's reachable if you have the 2.3L - but you need to be careful reaching in when the engine is hot. It's not reachable with the 2.7L. One solution is using a rod like a water meter key to turn the handle. Another solution is a permanently mounted rod that replaces the handle and extends up to above the core support. I'm not wild about these 2 options. Another supplier of a hidden winch set up rotates the clutch handle to the bottom of the winch and access is through a hole in the winch plate/skid plate. This needs to be a fairly large hole that you can get your hand in. I might look at rotating the clutch handle to the forward position and accessing through a small hole using a short key. But I'm open to other ideas!
 
Last edited:
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
OK. I unpacked the new OpenRoad winch this morning. Looks like FedEx dropped the box but no damage to t he winch.

IMG_8176.JPG


Even comes with a hat!

I test fitted it in the winch tray and it fits nicely. A little tight on the motor end but everything clears. Looks like I will have to relocate the control box to the passenger side over the motor..

IMG_8177.JPG


Steve, the clutch lever is VERY easy to operate and it works a bit differently than a Warn or other winches I have. It only turns counterclockwise and lifts up to disengage the clutch. Granted I have not tried it under any load (like when the hook is pulled tight against the fairlead) but it sure looks like it will work very easily.

Engaged:

IMG_8178.JPG


Freespool (You can see how the handle pops up a bit):

IMG_8179.JPG


The RC mount came with a control box relocation Bracket.

IMG_8180.JPG


So far so good! I think it will work well.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
That's how the free spool lever works on the old Dayton winches that I have, it seems to work well. The Daytons are so hard to pull in free spool that I power them out if I can't hook up and pull them with a vehicle, the Ramsey's I have aren't much better.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
That's how the free spool lever works on the old Dayton winches that I have, it seems to work well. The Daytons are so hard to pull in free spool that I power them out if I can't hook up and pull them with a vehicle, the Ramsey's I have aren't much better.
I miss-read your post about this. I thought you were saying it was hard to get into freespool mode because I have had this issue with my Warn and my Smittybilt. Pulling the line out in freespool is obviously a different issue. I'll let you know when it's installed and I try it out!
 
Last edited:
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
I took the Stroppe to Bronco Super Cel West this past week and ran a trail . . .

But first I need to tell the pre-story! I first took my trail rig and left the Stroppe at home. We did Grizzley Lake on Wednesday and if did great. Grizzley Lake is overall a moderate trail with the exceptions of a very hard gatekeeper and a very loose and steep shelf road section. At the end of the run I noticed the transfer was getting hard to shift. Then driving back to camp I had to hold the tranny shifter in 3rd or it would downshift to 2nd. I adjusted the shift linkage and it seemed OK. Next day we were going to run Chinaman's and I could not get the front engaged at all. So I scrapped Chinaman's. Trouble shooting I found I had broken the transfer case/doubler crossmember. So I borrowed a truck and used my trailer to take the trail rig home and bring the Stroppe back! (3 1/2 hours each way!).

On Friday we ran a new trail off Cottonwood Pass. Not real hard but narrow in some spots and very scenic. The Stroppe did awesome! Hardest part was avoiding tree branches to not get any scratches! The trail ended at a cabin on private land at over 12K feet.

Here are a few pics from above treeline.

IMG_8220.JPG


IMG_8223.JPG


IMG_8227.JPG


I spoke with Tom Broberg and he surprisingly said my 4-door Stroppe was the first 4-door at any of his events! So it got a lot of attention. I had to take a photo with a Stroppe painted Raptor from Liberty Firearms.

IMG_8230.JPG


Overall a good week! Now to weld up that crossmember!
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
I haven't worked on the Stroppe lately since returning from Super Cel. I'll get back on it probably later this week or next week.

In the meantime . . .

We went on a 2 1/2 week RV trip to Upper Peninsula MI and made various stops on the way there and back. Awesome trip! The stop in Lincoln NE at the Museum of American Speed turned out too be one of the top highlights of the trip. Incredible - the best car museum I have ever been to. I could start a new thread in Off Topic about this museum alone! If you ever are in Lincoln and have half a day be sure to go this museum and get a docent to give you a tour!

But back to the Gen6 . . .

As I've mentioned in other threads, Gen6 Broncos have replaced most Jeeps here for a lot of the year-round residents. We took a tour of a local ranch which was part of a local school foundation fund-raiser. We met in town and caravanned to the ranch for the tour. It's an 1,100 acre ranch at the base of West Spanish Peak that borders a volcanic dike wall geologic formation. It's the longest and tallest volcanic dike in the world! (I could start a thread in Off Topic about this as well!). Anyway when we caravanned to the ranch it was 4 Gen6 Broncos and 1 F250! They thought it was a Bronco parade! And after the tour they wanted us to line up for some promo photos (along side the Polaris UTVs that are used on the tour.)

IMG_8660.JPG


And here is a pic of the dike wall.

IMG_8636.JPG


That's not a cliff. It's a wall about 50 foot wide that is the same on the other side!

Here's is a view with better perspective.

IMG_8607.JPG


The ranch includes every thing in this photo from where the picture was taken to the dike wall. It was a great tour of a very interesting ranch.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
That’s cool! If you’ve never visited the area the geology is very unique and is very picturesque. Not to push @Scoop into a new job, is an excellent tour guide with a ton of local knowledge.
LOL!

Every year bus loads of geology students come to study the dike walls. There are numerous dikes in various stages of exposure and they radiate out from West Spanish Peak like spokes on a wheel. If you look along them they all point to the peak.

Steve, the arch we met at a while back is one of the dike walls on the other side of the peak.
 

ssray

Contributor
Sr. Member
Joined
Apr 19, 2010
Messages
921
Loc.
South Central NE
LOL!

Every year bus loads of geology students come to study the dike walls. There are numerous dikes in various stages of exposure and they radiate out from West Spanish Peak like spokes on a wheel. If you look along them they all point to the peak.

Steve, the arch we met at a while back is one of the dike walls on the other side of the peak.
I've seen the tunnel blasted by the CCC thats pretty cool....maybe it was you that posted it before. Need to go for real sometime!
 
Last edited:

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,147
Loc.
Lincoln NE
Hi Scoop, glad to hear that you enjoyed the museum in Lincoln. We here are blessed to have it. Speedway Motors, right next door. Puts on a Cars and Coffee event, on the last Saturday of each month. May through October. Participants are give free passes to the museum. So I get to enjoy this museum regularly. Next time you are in the area, look me up.
 
Top