Community
Buy / Sell
James Duff Rust Bullet Sexton Offroad
Bronco Tech
Ford Bronco Parts - Classic Vintage Early Bronco Parts
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.
JB Fab

JB Fab

Sponsor/Vendor
Bronco Guru
Joined
Last seen
Messages
1,339
Gallery
3

Latest activity Postings Attachments Images Gallery Albums About

    • JB Fab
      JB Fab reacted to WILDHORSES's post in the thread Ax15 clutch chatter with Like Like.
      To add to what's already been suggested I like to remove the rear driveshaft altogether and just use front drive to verify the issue...
    • JB Fab
      JB Fab replied to the thread Ax15 clutch chatter.
      Same exact combo (351w, Centerforce, ax15, Dana 20, 4:11, old school tight AF Detroit locker) except 35s Same issue... I know, sounds...
    • JB Fab
      JB Fab reacted to Grey owl's post in the thread Tarrifs with Wow Wow.
      They applied it on the shipping as well, I asked UPS for an explanation but they have not responded. Paid over 500 canadian for a...
    • JB Fab
      JB Fab reacted to admin's post in the thread Tarrifs with Like Like.
      Before this thread gets off topic, I'll just remind everyone that political comments/discussions aren't allowed on this site. So please...
    • JB Fab
      JB Fab reacted to AZ73's post in the thread China trade: What now? with Like Like.
      It's going to be over relatively quickly. I'd wait on anything you don't immediately need.
    • JB Fab
      JB Fab replied to the thread Tarrifs.
      Hey wait! I just confirmed the tariff rate US to Canada right now is 25%, someone charged you 49.5%????
    • JB Fab
      JB Fab replied to the thread Tarrifs.
      Were the charges from the supplier or the shipping broker? Goddamt! If they charged a tariff surcharge on shipping, I would go batshit...
    • JB Fab
      JB Fab replied to the thread D20 Rear Output Bearing Chewed Up.
      If the race spun in the housing, replace it (the housing).
    • JB Fab
      JB Fab replied to the thread China trade: What now?.
      My 2C...... I personally wouldn't buy a transmission a year early 'just in case'... warranty ticking down as it sits in the corner. A...
    • JB Fab
      JB Fab replied to the thread D20 Rear Output Bearing Chewed Up.
      Are you flat towing? It's hard to zoom in on your picture, is the jacked-up from the race spinning? What lubricant are you using?
    • JB Fab
      JB Fab replied to the thread Doubler for NP435 to Dana 20.
      ATV MFG (Herm the overdrive guy has them in stock), they also machine the idler gears for D18/D20s to use a bearing like a 205...
    • JB Fab
      JB Fab replied to the thread Doubler for NP435 to Dana 20.
      What about a 3.15 gearset in the D20? saves you needing to rework the drivelines, crossmember, shifting, etc......
    • JB Fab
      JB Fab reacted to Broncobowsher's post in the thread 6R80 Automatic transmission control module. with Like Like.
      Unless you are doing the complete drivetrain from the F150, no. The only stand alone controller is the aftermarket one.
    • JB Fab
      JB Fab reacted to EPB72's post in the thread 6R80 Automatic transmission control module. with Like Like.
      The PCM POWERTRAIN control module , does engine and transmission controls as well as can bus communication to allow most other control...
    • JB Fab
      JB Fab reacted to nvrstuk's post in the thread Anybody added a cat? with Like Like.
      If your rig is running right now, try putting a short pc of tailpipe or PVC or whatever to extend the pipes out a bit to copy the angle...
    Show older items
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Top