• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Recent content by broncnaz

  1. B

    Bending Stock Radius Arm Brackets

    Many people have cut them off and rewelded at the angle they wanted some have heated and bent them or replaced completly. I think even a few have been notched to allow a bend then rewelded. Lots of ways to do it. If one side appears not to be welded that its possible its been that way since it...
  2. B

    302 oil pump not pumping?

    its a gear pump if it spins it should start pumping these rarely fail even if worn it should pump but it may no have much pressure. might take a few minutes if the filter is new as it has to fill up as well. also keep in mind you should feel it take more torque to turn the pump once it starts...
  3. B

    =trans swap NP435 to T19

    should be pretty straight forward swap use adapter off the NP the 1 in length difference shouldn't be a issue unless your lifted then you may want to verify front driveshaft length. May have to cut the tunnel a little larger if it is close on the NP currently there but otherwise it all will...
  4. B

    Recent feedback on mechanical pump

    Most likely if you drive the bronco a lot it will last a long time. Just not as long as they did in the old days. If your bronco sits a lot it wont last long. I was going thur the cheap pumps every 6 months on my 71 as it would sit a lot I think I even had one Napa pump that didn't last long...
  5. B

    C4 woes, possibly fluid?

    What I've always heard is dont switch oil types in automatics. Supposedly when you rebuild you can run a different oil than stock but once its been run it needs to stick with that oil. So what your builder recommends should be what you use. But as was said friction material may be a factor. old...
  6. B

    Centering the front axle

    That will work just fine. If you have a helper and your steering is still hooked up you could have them just turn the steering wheel and hold it where you want it then install the track bar.
  7. B

    Front Drum and Hub come apart?

    The problem I see if your pounding them out while on the axle is your beating up the bearings or at least the inner bearing not the best idea IMO.
  8. B

    Is the caster Shim needed for front disc conversion?

    could have been for camber as well. I ending up putting adjusters in mine that helped the camber and added some caster while I was at it. before the swap I didnt have camber issue dont know if it was the knuckles or what. but definitely keep the adjuster in case you need it later on.
  9. B

    New 1:64 Matchbox Bronco

    Score this this morning. Might be the pinnacle of collecting lol.
  10. B

    splined shaft coupling. female to female

    Might try advance adapters or Novak
  11. B

    When to spend on an improvement and when to let it go?

    Well dream broncos are great but not ones you intend on selling. A good body will get you more money than anything else you do. A running engine is a bonus for you right now if its not smoking or using oil then its fine while unknown is not ideal no smoke or oil consumption is good. No reason...
  12. B

    Msd box

    B cams are not known for good idle and more tuning is likely needed. Highly doubtful its ignition related even then a msd box is not needed. I personally dont care much for them seen to many fail yes stock systems fail but Ive seen way more msd's fail for the numbers that are out there stock is...
  13. B

    TRO with 2.5” lift advice needed:

    I did TRO with 2.5 in lift adjustable trac bar and no riser or drop bracket. My bronco handles really well. They are not must do items on that size lift if you have the adjustable trac bar and drag link
  14. B

    Bronco Track Width

    Anywhere between 57 and 58in. Its not uncommon for the front to be slightly wider than the rear. Ford was no wheres near as bad as GM was on different front to rear track widths.
  15. B

    IN Sold

    AA used/sells hurst shifters to clarify for the picky
Top