• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bending Stock Radius Arm Brackets

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
...using the face of the "doughnut" at the datum....
That's not a particularly precise surface to use; especially with the coating on the frame.
The old one I took out was really smashed to hell on the botton side from being pinched...
That suggests that the problem existed for some time; not just a recent change.

Looking more-closely at your pic, I see what might be a witness mark from the bracket rotating around its bolt. Is it that, or just some random dirt smudges? Is there any corresponding mark on the other side, or on the bottom? If there is, and you try to adjust it back, I wouldn't use heat - I'd use slow hydraulic pressure, like a bottle jack pushing it. The trick will be giving the jack an anchor on the frame strong enough to push against. So it might be easier to pull against the rear crossmember with BIG chain (the cross-section of 1 link needs to approach the cross-section of that RA bracket where the bending will occur).

cbc.jpg


Another problem I notice that's almost certainly contributing to the RA frame bushing pinch is the "Bronco lean" you have in the way the RAs are clamped to the axle tube. Yours is maybe only an inch, but every little bit hurts. Assuming the floor is reasonably flat over this distance, and the jack stands are set at the same height, and assuming they're both touching the axle tube surfaces (not on some random lump), the RA tips should touch the floor equally.

cbc1.jpg


If you want everything "right", you should loosen the RA bolts at the axle end, and try to neutralize them around their bushings so the arms are perfectly parallel.
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Good eye on the witness marks and the distance from the floor Steve?.

Hey! Maybe putting the brackets on crooked was how Ford corrected for Bronco-lean, right on the assembly line! Ha ha!
Actually, I guess that’s not even a thing since the frames were already built, I believe, in another facility.

But with all this talk of correcting your angles, you might as well fully correct for any suspension lift you’re including in the equation.
That way, the bushings fall at a natural compression when the vehicle is at ride height.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
I can't tell if your passenger side bracket is welded on, but the drivers side definitely does not look welded. If not welded and it's just that single bolt I would think you can loosen the bolt and put a small spacer to fill the gap to straighten things out. But going back and reading your posts about trying to heat it and using a big pry bar makes me think that it's definitely welded. But then again why is the drivers side not welded? Or am I completely wrong and just looking at the wrong parts?
They are both welded. Just hard to tell from picures. The passenger side is the one I need to move.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
That's not a particularly precise surface to use; especially with the coating on the frame.

That suggests that the problem existed for some time; not just a recent change.

Looking more-closely at your pic, I see what might be a witness mark from the bracket rotating around its bolt. Is it that, or just some random dirt smudges? Is there any corresponding mark on the other side, or on the bottom? If there is, and you try to adjust it back, I wouldn't use heat - I'd use slow hydraulic pressure, like a bottle jack pushing it. The trick will be giving the jack an anchor on the frame strong enough to push against. So it might be easier to pull against the rear crossmember with BIG chain (the cross-section of 1 link needs to approach the cross-section of that RA bracket where the bending will occur).

cbc.jpg


Another problem I notice that's almost certainly contributing to the RA frame bushing pinch is the "Bronco lean" you have in the way the RAs are clamped to the axle tube. Yours is maybe only an inch, but every little bit hurts. Assuming the floor is reasonably flat over this distance, and the jack stands are set at the same height, and assuming they're both touching the axle tube surfaces (not on some random lump), the RA tips should touch the floor equally.

cbc1.jpg


If you want everything "right", you should loosen the RA bolts at the axle end, and try to neutralize them around their bushings so the arms are perfectly parallel.
Yep, I am replacing the C-bushings also. This picture was taken with the old bushings in and before I took off the radius arms. The dirt marks you see are really just that, The one with the dirt marks it the one I already tried to move. It is definitely welded. Hahaha The face of twhere the bushing sits it there I am measuring the angle.
Screenshot 2025-10-10 121509.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Being partially welded on was what kept me on the bending tack, rather than just cutting through the welds and moving the thing like I should’ve been all these years.
Back then I wasn’t comfortable with cutting off factory welds. Now I would have no problem with that.
In fact, with all the figuring, factoring, and fixturing needed for bending, it’s probably easier to get an angle grinder and cut through the welds and relocate the bracket as needed.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
Being partially welded on was what kept me on the bending tack, rather than just cutting through the welds and moving the thing like I should’ve been all these years.
Back then I wasn’t comfortable with cutting off factory welds. Now I would have no problem with that.
In fact, with all the figuring, factoring, and fixturing needed for bending, it’s probably easier to get an angle grinder and cut through the welds and relocate the bracket as needed.
Hadn't thought about that. I may decide to do that instead.
 

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
Crawled under my passenger side and that thing is welded fully. Based on the 90 degree bend plate I don't see how you could be able to bend it. I think you're going to have to cut it off. I'm calling the large flat side the plate because it looks kind of like a steel plate to me. there is no way it will bend without buckling the plate. Red circle is the weld and the long black arrow is pointing at what I'm calling the plate.
 

Attachments

  • radius arm bracket passenger side 1.JPG
    radius arm bracket passenger side 1.JPG
    136.2 KB · Views: 134
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
Crawled under my passenger side and that thing is welded fully. Based on the 90 degree bend plate I don't see how you could be able to bend it. I think you're going to have to cut it off. I'm calling the large flat side the plate because it looks kind of like a steel plate to me. there is no way it will bend without buckling the plate. Red circle is the weld and the long black arrow is pointing at what I'm calling the plate.
Yea I see the same thing you do. I guess I was just hoping that it would give enought under heat to move, but I do agree that it would have to buckle to move. May end up just cutting the dand welds and re-weld. Good thing I just bought a welder.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I watched one of the fabricators at Hanson Enterprise (the good bumper people before they became the bad bumper people) take a standard cutting torch and cut those and the spring hangers off of Bronco frame and hardly leave a gouge mark as to where the welds used to be.
It was a work of art, and a thing of beauty to watch.
He cut off four spring hangers, and two radius arm brackets in less than 10 minutes.
(That Bronco actually ended up becoming the red buggy that member mtfit had for a while)

Kind of embarrassing to think I was spending so much time thinking about how hard it would be to get it all done.
Then again, it wouldn’t be the first time I fell prey to analysis paralysis.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
So the torch heating worked great! No buckling of anything. Just heated both sides of the bracket to slightly glowing. 1st pic is after, second pic before.
1000015269.jpg
1000015272.jpg
1000015268.jpg
 
Last edited:

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
...I do agree that it would have to buckle to move. May end up just cutting the dand welds and re-weld.
Do you hear what you're saying? If it was NOT buckled right then, then you're saying that it MUST be in the factory location. So why would you move it? If you ONLY adjusted the axle ends of the RAs, you'd probably see the frame bushings equally-pinched.
So the torch heating worked great! No buckling of anything. Just heated both sides of the bracket to slightly glowing.
The problem is that it doesn't ONLY temporarily soften the steel. Even after it cools to room temp, the steel that you heated is softer than it was before. You should try to remember to re-check this after a year or so. The difference between L&R surfaces is what you need to know, which automatically eliminates any tilt in the frame.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
Do you hear what you're saying? If it was NOT buckled right then, then you're saying that it MUST be in the factory location. So why would you move it? If you ONLY adjusted the axle ends of the RAs, you'd probably see the frame bushings equally-pinched.

The problem is that it doesn't ONLY temporarily soften the steel. Even after it cools to room temp, the steel that you heated is softer than it was before. You should try to remember to re-check this after a year or so. The difference between L&R surfaces is what you need to know, which automatically eliminates any tilt in the frame.
I moved it because it was obviously not where it was supposed to be either by poor placement during build or some previous damage. I have seen signs that my Bronco had been wrecked at some point before I got in in 2001. I moved it to be the same angle as the driver side bracket is, so now they are equal. I only moved it a few degrees so it wasn't likely enough to cause a buckle one way or another. Yes I am aware that heating of the steel over 1100 degrees can cause some changes in the metallurgy and it could be a little softer than original, so I will keep an eye on it. I heated it only enough to be barely visible color change.

Thanks for everyones comments. I have moved to the next phase which is cleaning up of the axle and radius arms getting ready for re-installation. Went ahead and ordered now bolts for the radius arm caps and castle nuts for the ends.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Many people have cut them off and rewelded at the angle they wanted some have heated and bent them or replaced completly. I think even a few have been notched to allow a bend then rewelded. Lots of ways to do it. If one side appears not to be welded that its possible its been that way since it left the factory someone forgot to weld it up. But from your pics it almost looks like they were welded at some point so maybe a PO had a accident and they were cut off to adjust or replace and not rewelded properly or at all.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
Many people have cut them off and rewelded at the angle they wanted some have heated and bent them or replaced completly. I think even a few have been notched to allow a bend then rewelded. Lots of ways to do it. If one side appears not to be welded that its possible its been that way since it left the factory someone forgot to weld it up. But from your pics it almost looks like they were welded at some point so maybe a PO had a accident and they were cut off to adjust or replace and not rewelded properly or at all.
They were welded but it is possible that one of them could have been replaced at one time. I media blasted the radius arms and painted last night and I noticed that the casting/part number starts with C6 which would indicate the radius arms came off of a '76 bronco. My Bronco is a '71.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
"C6" or "D6" in those radius arms?

Brackets angled in different directions could result a mild form of the dreaded Bronco Lean. Same amount of force is going to compress the bushings the same amount. So just hanging free of the axle the arms won't be at the same angle. If the drooped arms are only a couple of degrees different I wouldn't worry about it, but with one bracket pointing down and the other pointing up I doubt that would be the case.

euw, hate drop radius arm brackets. Not even on a pavement queen. I'd go with longer arms even for just pavement.
 

47WDX

New Member
Joined
Apr 1, 2025
Messages
5
C6 indicates a part that was engineered in 1966 with a C6 engineering number cast into it. An engineering number is not a part number.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
C6 indicates a part that was engineered in 1966 with a C6 engineering number cast into it. An engineering number is not a part number.
I think you are right. I was thinking C is inthe 70's but it is D in the 70's. Makes sense. I didn't know about Engineering numbers. Interesting.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
And probably the same two, or three radius arms were used from’66 to’79.
From 66 to 77 at least, I think there were only two.
Those for the Broncos with the smaller spring cup holes and those for the pick ups with larger spring cup holes.
But I don’t know that those was exclusively used, or if they went back-and-forth and made changes over the years.
The only big chance I think would’ve been the addition of the lower shock mounts to the front radius arm caps on 78 and 79 full-size. And maybe additional holes stamped in for swaybar mounts perhaps?
Whether that denoted an entirely new radius arm number, or just a revision number, I don’t know.
 
Top