• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Recent content by Geiri

  1. Geiri

    Duffs Long Arm bracket weld

    Preference question I guess... I am just about to weld those on. Thinking no bolts. For those of you that have gone that way how do they hold up and do you weld the bolt holes to? It would be nice to see photos..
  2. Geiri

    23 gallon fuel tank- how to build. Plans

    Are you in a position to convert to metric and share afterwards?
  3. Geiri

    Rust between body layers

    So this is the a photo of my old 1976 Body. I know the rust goes deep in there between the layers. This seam will be sand blasted, but what can be done more?
  4. Geiri

    New build overheating

    Is this the highest point? Higher than the radiator fill cap?
  5. Geiri

    My Edelbrock Pro-Flo 4 Install

    I have looked at M1A1 at WH Actually I think I would go with a Locally made tank. I was hoping to be able to use my stock tank, But next on the list was to make a tank for Coyote fuel pumps. I am running another project with a 2019 Coyote and I would be nice to be able to make two identical...
  6. Geiri

    My Edelbrock Pro-Flo 4 Install

    Thank you I think so to. It's just a regular valve from Summit
  7. Geiri

    My Edelbrock Pro-Flo 4 Install

    Thank you for the write up, It's very helpful. I have this 302 ready almost ready to go into a 1976 Bronco. I just bought it locally here in Iceland. It's a freshly rebuilt 1995 302 with E7 heads Would you advice against using the stock fuel tank? If not, what measures would I need to take?
  8. Geiri

    Full Width front D44

    I am installing a Full width Dana 44 from a 1978/9 Ford Bronco. Can I use the 66/77 radius arms or do I need the Bronco arms? Also can I use the stock wedge location on the 78/9 D44 or do I have to move them inwards? They are casted on . I have the Duffs Full Width Offset Coil Buckets.
  9. Geiri

    Dana 44 hp bracket and wedges question

    Thank you. Is that chunk of steel up there the trackbar mount?
  10. Geiri

    Dana 44 hp bracket and wedges question

    Did the come so close to the Wedge? I added two photos to post.
  11. Geiri

    Dana 44 hp bracket and wedges question

    I just bought these Full width and believe they are 78-79. The wheel pattern is 5x5.5 Going under a 1976 Bronco Someone welded leaf spring seats to them and I am in the process of cutting and grinding. Under the leaf spring seat on the Passenger side there is a bracket that looks like and...
  12. Geiri

    What is the correct bracket for this steering pump?

    I am looking for a friend. It looks like a Saginaw pump For a 302. Is there an aftermarket Bracket available for this pump?
  13. Geiri

    1974 Lower steering column bearing

    This is a friends 1974. The steering shaft is rattling in the lover tube. I am wondering what parts he needs to get this fixed. He does not want to pull the column out. Are those two Items enough or is there more to it?
  14. Geiri

    Opinion on drilling the support under Cowl?

    I just made a new bottom for the support under the Cowl. The bottom was rusted out. I cut it and welded a new bottom in place. The question is should I drill it from the bottom up in each corner, so I can get some Prolan or similar in there? What do you think?
  15. Geiri

    Floor pan cowl lip cut or stay?

    So I had to grind away more of the outer edge where the lip was to allow for even better seating. You can see on this photo that the floor plate is not seated correctly there, because the outer edge, where the lip was needs a little grinding. Seam sealer will cover this all The next two...
Top