• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Explorer rear discs: not working at all! Thoughts???

OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I have run the numbers just gotta find them. Either way I think we can all agree 250 ain't gonna cut it.

All I can come up with is to use one of my old drum cylinders, secure the pistons, connect it with a short hard line at the MC, and use one of my adapters for the gauge to measure pressure.

I guess I could just measure fronts then swap the lines at mc and measure again. Just requires more bleeding.

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Can you please be a little more specific about your adapter? I don't see how it can be done.

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
There are adapters out there just not real common. Parts sotes can get them if your parts guy is good. but Id probably look at getting a short piece of hard 3/16 brake line with metric fittings and a standard fitting cut the brake line and install the standard fitting and flare the end. Then you would probably only need a metric union to hook the line to your gauge.

Just a short rundown if I got it right. New MC, new hard lines, no prop valve, Old explorer lines, 250 psi showing at both rears, I would begin to suspect blockage somewhere in the rear lines. soft lines from MC? or soft line from frame to axle.
Brake PSI is relative to how much pressure you put on the pedal so to get your 250 how much pressure do you think you used to push the pedal?
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Correct. Soft from frame to axle. A shit ton of foot pressure. More to come...

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 

MarkH@Wildhorse

Contributor
Full Member
Joined
Dec 14, 2012
Messages
282
Loc.
Stockton, CA
Can you please be a little more specific about your adapter? I don't see how it can be done.

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod

I can't only because I have no idea what the sizes were.
I just found the threads on the gauge, then the threads I needed to go into the a line/block/ whatever. then I just hit up the hardware store where I could find a brass fitting (brass because it cuts easy) that had enough meat on It for a tap / die.
I though that gauge was 1/8 pipe, but you said it was different, I've not pulled out my gauge out in a few months so I'm guessing I'm wrong.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
When u get a chance, can you please look into what parts and fittings you used for the gauge?

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Scrap that. Found a -02 FPT x -04 FJIC swivel adapter and a -04 MJIC x Male INV 3/8-24

Part numbers are 2242-2-4s and FMC2927

Cost about $10

Too bad I'm out of town for 3 weeks.

e9ejebun.jpg


Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Ready?

Rear at mc is 250psi too.

Unfortunately, so is the front. Not sure how i am stopping with only front calipers that only get 250psi.

Gotta call WH an CPP tomorrow.

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Btw... Played with the rod adjustment between mc and booster just to be sure.

Out 1 full turn: 250
Out 2: 150
Out 3: 150
In 4: 150

My rod must be adjusted correctly already.

I suspect a bad mc.
Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Id say your input effort is less than 75lbs a 1 1/8" MC will/should develop 453 lbs of presure with 75lbs of input and a 6-1 pedal ratio(which is about what broncos have). If you had a 1in bore MC the same 75 lbs would net you 573 PSI. Now say you have a panic stop and used 150 lbs of input pressure on the pedal you would get around 1300 PSI out of the 1 1/8 bore MC.

Basically you either need more input pressure or swap in a smaller MC for reduced pedal effort.

High MC pressure is not always needed to stop. While 250 PSI my seem low when you factor in the caliper piston size the amount of pressure generated on the brake pads is much higher.

There's a lot of math involved in figuring out all the sizes of the MC piston vs the caliper pistons. It may pay to find a site that has a calculator and do all your inputs to see what you come up with.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I was standing on the brake pedal and i weigh 170.

Way ahead of you on the math. Looking at needing 1100 front and 300 rear.

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Attached are my calculations via BillaVista. The weight / CG numbers may be off but ultimately the net pressure should be the same regardless of the shift from front to rear.
 

Attachments

  • brakecalcs.pdf
    13.4 KB · Views: 73

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
crap dude I really dont know what to suggest now. You have the worst brake issues I think I've ever heard of. At this point all I can say is it must be the MC again if you cant builld more than 250 PSI front and rear. Not sure if your using rebuilt or new units but I would recommend going with a new unit. You never know what your getting with a lot of the rebuilt ones.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Brand new cpp mc from wh. I should get an award or something, right?

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
You could get an award for the most detailed brake parts test for sure!

Don't go spending money on another different master just yet. Even though doing so would be a legit test in itself of course.
You've already swapped at least one new master without it helping, but that was many (many) parts ago now, so let's go there and see what we can do with the existing type.

Just sent you an e-mail.

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Got your email . Thx.

The folks at cpp are going through all this with me one last time before we swap a mc.

They raised an eyebrow when they found out my gauge doesn't have a bleeder.

Waiting for them to get back with me.

Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Yeah air pressure in the gauge can cause issues. But the fact is your brakes are not working. So Id say the pressure reading is probably close. looking back through when you swapped ona now working unit your brakes worked. then when you swapped the new MC on again no worky. So only one conclusion there.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Re-attack.

I finally had an opportunity to install and test the new MC from WH and, though I measure 700psi, my rig is still as sluggish to stop as before.

I know it has been a few weeks, but uncle sam has had me pretty busy.

Leaving for Uwharrie in 2 weeks. Would be nice to have brakes on the wat from Tampa to NC.

Any other suggestions?



Sent from my SAMSUNG-S3 using Tapatalk 2 on CyanogenMod
 
Top