• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Strange EFI Issue

OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
I pulled codes this morning:

KOEO -
23 - Closed throttle voltage too high or low
81 - Air management 2 circuit failure
82 - Air management 1 circuit failure
85 - Canister purge solenoid circuit failure
84 - EGR vacuum solenoid circuit failure

CM -
33 - EGR valve opening not detected
96 - Fuel pump secondary circuit failure. EEC did not sense battery voltage on the fuel pump monitor circuit

Note that I have the RJM EGR delete installed with no EGR valve and no canister to purge!

Anyone know anything about the air management circuits? Would the fuel pump secondary circuit control the fuel pump on hot starts?

After reading about the TFI module, I think I'll start there.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO

Jim thanks. I'll run through the test procedure for code 96 shortly.

I replaced the TFI and it didn't help. I checked for spark and that seems fine. Fuel pressure at the rail is 35 lbs plus (is this low??). Fuel pumps runs when cycling ignition even when it won't start. I'm starting to think the ECM - maybe not activating the injectors when hot? I have a spare I'll swap in and give that a try.

Again, after it sits for about 10 minutes it starts right up and will run until I shut it off. Then it won't start????
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
The 23 code is the problem. None of the others are significant if the pump is working.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
What is your fuel pressure 2 minutes after shutting the engine off?
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
fuel pressure is Ok, I have run down to 25 psi with out issues

start looking into code 23
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
OK I'll set the TPS today.

Yesterday I did swap computers to one from a 91 Cougar - "L1C". It seems to have helped the hot start issue but it now runs like crap! I'll set the TPS and swap back in the A9P computer and see what happens.

Thanks for all the suggestions.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
Over 2V at closed throttle! I need to make the TPS more adjustable (enlarge the screw slots) in order to get it in the correct range. Input is 5.01V.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Please don't swap computers like that or you will fry something. They are not made to be interchangeable as there is a ton of variation in wiring and pinouts.

Attached is a list of acceptable program codes for the 5.0 stang MAF and SD.

A TPS will drift and go bad over time. Make sure you have good smooth readings throughout the entire sweep.
 

Attachments

  • Engine - EEC Program Codes_1.pdf
    17.5 KB · Views: 54
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
Please don't swap computers like that or you will fry something. They are not made to be interchangeable as there is a ton of variation in wiring and pinouts.

Attached is a list of acceptable program codes for the 5.0 stang MAF and SD.

A TPS will drift and go bad over time. Make sure you have good smooth readings throughout the entire sweep.

L1C is on the list for MAF/Auto. Does that mean it's acceptable or are just the ones listed as 89-93 Mustang compatible with the A9P? Thanks.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Just mustang. That page was extracted from a comprehensive list including all models and variants.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
L1C is on the list for MAF/Auto. Does that mean it's acceptable or are just the ones listed as 89-93 Mustang compatible with the A9P? Thanks.

I think the cougar efi wiring was similar to the '94-'95 mustang. Not compatible to just swap computers with the pre-'94 mustang stuff.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
I have not run it yet - I'm topping off the battery with an overnight trickle charge. The the old TPS tested bad. It read about 1.6V to a little over 2V over the entire range of throttle movement. I have installed a spare TPS I had and it reads 0.89 at closed throttle and a little over 4V at WOT. I'll let you all know tomorrow how it runs. And yes I reinstalled the A9P computer.

Thanks for all the help. Pretty sure code 23 was the problem as several of you indicated.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
Yup, ran it today. Bad TPS. It may have been bad for a while and was getting worse. Runs great now with the A9P and idles much better and at a lower RPM. I'd been having trouble getting it to idle below 1000 RPM for the last year or so and now it idles at around 800-850 (C6). And it starts back up hot now!

Again, thanks for the help!
 
Top