TN Super Celebration parts thread. Post what you’re bringing to sell here

[widowmaker77]

I think I have s few units not sure on brand, do you have a picture?

I saved this pic of one from a post on here.

 

[Zeke]

4/8/25 Additional Items added and Photos are available in my Gallery.

Here are some items I can bring if there is interest, so let me know.

- 1974 6 turn PS Box with cooler, stock pump and bracket. Will need at least a re-seal $450
- Ranger/Sport Door Window Bright trim. Will need polishing $100 both doors
- 4-15"x7" Slot Mag Wheels $400
- 1 1965-1967 era Galaxie Dog Dish Hubcap $30
- 1 1978 F100 Dog dish Hubcap (dirty and has a couple dents) $15
- Grey Colored seatbelts aftermarket (pair) $100
- Parking Brake Assembly $80
- Brake bracket with small pad pedal $100
- Hood Latch $40
- Used 302 fender emblem good for a patina built $15
- NOS Bronco Sport emblem. I bought this 25 years+ at the fall Hershey AACA swap meet (before they started repro. them). Shelf wear only $50
- 4:11 Dana 44 gearset. NIB, never installed $200

Maybe more as I go thru the shop.

Thanks,
Zeke

 

[sk1nw4lk3r]

I'll also bring a T shift Dana 20 in good working condition

 

[1969miller]

Good morning, I have and can bring the following if they are paid in advance. Coming from CA.

(1) HP D44 78-79 Housing only, nice wild horses track bar riser bracket welded to it. Bearing caps are there. $200

(1) 76-79 F150 brake setup includes knuckles, brake brackets, hubs, rotors, and calipers. All parts are used and should be gone through before installing. $500 for the set.

(3) complete explorer EFI systems. Includes upper and lower intakes, all engine harness intact, all engine bay/fuse box wiring intact, fuel rail and injectors, includes ECU also and keys for PATS where applicable. One is a 1996, one is a 1998, and one is a 1999. These are explorer harnesses and have not been modified for bronco use. Save yourself a junkyard trip and buy one of these packages!

C6 transmission listed here: https://classicbroncos.com/forums/t...possible-free-delivery-to-tn-supercel.326971/

Various height lift springs ill get back to folks on those when i figure out lift height etc.

-Morgan

 

[doublehfarm]

Have a new James Duff J shifter never installed. $ 150

 

[Molesworth1991]

Let's get it started!

I have a roll bar with the short legs that attach to the top of the rear wheel tubs, blasted and coated in flat black epoxy. Verified it will not work with a half cab but will with full top or bikini, Upright is too straight, not slanted $150.

Also, Black Rampage soft top. Good shape, clean tinted windows, with small rip in the right rear adjacent to the tailgate (see pics), would not leak at this point. All hardware and fasteners. $250 (SOLD)

Taillight housing repair pieces. Complete housings without the tabs. $60 for the pair (SOLD)

Windshield frame. Has some minor rust through $100. In Epoxy primer

Is roll bar and windscreen wiper motor still available? Thanks

 

[hyghlndr]

Metal dash cover overlay, just dusty in picture - $80

 

[hunter1]

Is roll bar and windscreen wiper motor still available? Thanks

Yes to both

 

[OlliesBronco24]

I am trying to find original mirrors. I am really after the remote mirror for the driver side or the chrome passenger one.

 

[Muddy1966Bronco]

I just finished a painting in partial trade for parts and I have enough time I could do 2 more and bring to Super Cel if I get requests soon enough. These are completely hand done. I can change backgrounds or eliminate things you don’t want. I just need a high quality photo of your Bronco in the position you want it.

16x20, $100

Because of the amount of hours and time into a personalized Bronco painting, I’d just ask 1/2 down to do it. PayPal or Venmo. PM me if you are interested!

 

[hyghlndr]

That is my red Bronco above, beyond thrilled with how it came out. I can't even draw a stick figure so I am amazed by the talent.

 

[widowmaker77]

I think I have s few units not sure on brand, do you have a picture?

@hyghlndr was wondering if you had a unit like in the pic I posted?

 

[hyghlndr]

@hyghlndr was wondering if you had a unit like in the pic I posted?

I am going to check i have way too much buried away. I know I have the center units, need to check on the vent extensions.

 

[widowmaker77]

I am going to check i have way too much buried away. I know I have the center units, need to check on the vent extensions.

Ok thank you!

 

[hyghlndr]

Blue houndstooth Ranger DOOR panels and REAR panels. Door panels are still packed up and rear panels were opened for pictures when I bought them.

$2500 or trade, save yourself a 3 year wait!

 

[hunter1]

Let's get it started!

I have a roll bar with the short legs that attach to the top of the rear wheel tubs, blasted and coated in flat black epoxy. Verified it will not work with a half cab but will with full top or bikini, Upright is too straight, not slanted $150. (SOLD)

Also, Black Rampage soft top. Good shape, clean tinted windows, with small rip in the right rear adjacent to the tailgate (see pics), would not leak at this point. All hardware and fasteners. $250 (SOLD)

Taillight housing repair pieces. Complete housings without the tabs. $60 for the pair (SOLD)

Windshield frame. Has some minor rust through $100. In Epoxy primer

C4 Bronco transmission with pan fill dipstick, flex plate, torque convertor, spacer plate, and starter. Complete with J-shift T/C. Looking to trade for an AX 15/NV 3500 complete with adapters, or $1500.

Windshield wiper assembly. Complete with mounting bracket and linkage. $100 View attachment 942796

Bump. Added a couple more items

 

[hyghlndr]

Minty, pretty much nicest I have seen. $1650

2 degree bushings $10

Manual steering box - make offer

2bbl Carb and spacer, would suggest rebuilding. $50

Factory trackbar- make offer

Hood prop rod- $10

 

[ohpoo2]

Any intrest in this old bumper. Had it awhile and has got some rust and pitting. Gonna throw on trailer and bring to townsend with a bunch of other odds and ends . Would like $100. But needs a good home. Bronco not for sale
Thanks

 

[hyghlndr]

Looking for:

Nice 67-77 hubcaps
Aluminum Slot wheels

Thanks

 

[jimmyk]

New 6R80 Adapter and Crossmember. I bought last year and went a different direction (Electric Transfer case).

Was 950 new, will take $600, or will trade for a really nice set of 69-77 doors.

I also have a few 6 turn boxes, 250 each, 1 rebuilt 4 turn for 450.