• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

The Ballad of Ol' Rusty

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
And when you replace your main battery ground cable to the engine, take the opportunity to correct a few things.
1. Make it black. I know people can figure out its ground because it’s bolted to the block, but black means you, or anyone else doing any work for you, won’t make any mistakes up at the battery end.
2. Make sure it’s a good size. A 4-gauge cable is minimum, 2-gauge is a nice upgrade.
3. Make it longer and mount it to the correct location. Yes, longer is not always better. But getting it closer to the starter motor and off of the cylinder head is enough to warn the longer cable. Up on the cylinder head might work, but it’s not optimum. Run it down and mount it lower on the block, and closer to the starter motor.
Bolting it to a threaded hole that’s often there on our engines, or right to one of the starter bolts is not a bad practice.
4. And at least it gets you a new cable, because that old blue one looks fairly long in the tooth.

No reason to replace the starter if the old one is doing its job. But new cables are rarely a bad thing.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Hmmm, interesting. Rereading I see that you do have new cables on there. It was obviously not factory, because it was larger. But it didn’t look brand new.
Anyway, keep those suggestions in mind for the next time you need a new cable.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
Hmmm, interesting. Rereading I see that you do have new cables on there. It was obviously not factory, because it was larger. But it didn’t look brand new.
Anyway, keep those suggestions in mind for the next time you need a new cable.

I picked up new cables, installed some of them, But I have not installed the new ground yet. I will have to check and see if it is 2ga or 4ga.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
'Dehydrated' coolant gets like that. Wouldn't worry about it too much. I'd do a flush with this water pump still in place. Then replace it.

Strongly recommend going with a Stewart Components water pump. They outperform all of the other good options that I've seen. Their page is a bit wonky in figuring out which pump of their is the correct one, but it is worth the effort.

If you're thinking of going with the Explorer front dress, this looks like a good time to make the switch. I'm guessing that's not the plan, but thought that I'd mention it just in case.

I have thought about switching to the Explorer front dress as I know that is a popular change. I need to look into what all that entails a bit more. I know our local salvage yard has a couple V8 Explorers. So I would guess I have access to what I need.


Of course the original goal was to do as little as possible to get it driving and then figure out where is the most pressing areas to spend my limited funds.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
This evening I had some time, so I hooked the garden hose up to the cooling system and tried to flush it out as best I could. It was nasty water that came out. I filled the system back up and fired Ol Rusty up. I took my son for a ride around the block in it for the first time. The transfer case popped out of gear again. It also seems to be whining. My son was over the moon, riding in it. He told me that the bronco seat was the most comfortable seat he has ever sat in. He wondered if it could become his assigned seat. When we got back I had built up pressure in the system. The heater core valve could not withstand the pressure and gave up.

1755228210373.png


My son switched out the old license plate (which expired in 04) and replaced it with our new one. Unfortunately, the 1973 plate in Kansas was green; in 1974, it was nearly the exact same orange as the Bronco, which would have looked great. I think the green looks good, though.

1755228383805.png
 
Last edited:

joebronco73

Contributor
Full Member
Joined
Mar 16, 2009
Messages
276
Loc.
Lago Vista, TX
I took my son for a ride around the block in it for the first time. The transfer case popped out of gear again. It also seems to be whining. My son was over the moon, riding in it. He told me that the bronco seat was the most comfortable seat he has ever sat in. He wondered if it could become his assigned seat.
That's freaking awesome. I think you've officially made him a forever-Bronco fan.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
Even though it was jalapeno hot here today, we spent some time on Ol Rusty. My son tended to retreat inside a bit more today than last time working on it. I dont blame him. I pulled the radiator. The other day I had opened the drain cock, it was very difficult to turn. I couldnt really get it to seal back up. So i figured dealing with that would be much easier out of the bronco than in it. Plus it gave me much more room for pulling the water pump.

Ol Rusty had what appears to be a homemade AC compressor mount, although i have found no signs of an AC ever being installed. This thing was a bit of a beast to get off. Then I pulled the water pump. It seems as if the old dried up antifreeze formed some sort of limestone type material and had blocked the pump off completely:

1755395794773.png


1755395817262.png


1755395840639.png






The soft limestone was about an inch and a half to two inches thick. For a while I assumed the entire block was filled with it. But I managed to break through it and out poured actual antifreeze:




After that I was able to shove a hose in there and flush things out. It was pretty nasty looking at first. By the time I got the video going it had cleared up quite abit.


Since it was so hot, I decided to take the opportunity to get the power washer out and go at all the dirt and grease again. I will say that i was thoroughly soaked and amazingly dirty, when I finished. My concrete driveway almost looked like a dirt road. It was a big improvement again.

1755396464584.png


I also managed to fix my washing machine today. So i should have some time available tomorrow to work on it some more.


Has anyone else seen that type of gunk in their coolant system? Is there anything else you all think i should do before i put it back together? I planned to run some coolant flush through the system once I get it back together.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Seen it many times in years passed, but luckily never on one of my own rigs. Usually just there at the openings, luckily too.
Since you've gone this far, I would actually flush it with one of the super-strong 2-stage cleaners. Or at least one of the modern ones that's super strong.
The 2-stage ones are so strong, that after you use them initialy, the second stage is a "de-activator" (not the correct term) to stop the strong solvent reactions going on inside the engine.
Did one of those on my Bronco back in the early '80's and that darn stock radiator looked brand new inside until I removed it many years and miles later.
I'm sure they have improved methods today, but boy howdy did that flush work!

Where is the A/C bracket you're talking about? Was it on the passenger side, or driver's side? If passenger and part of the alternator bracket, perhaps there was a Thermactor (air pump) on your rig at some point.

Paul
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
Seen it many times in years passed, but luckily never on one of my own rigs. Usually just there at the openings, luckily too.
Since you've gone this far, I would actually flush it with one of the super-strong 2-stage cleaners. Or at least one of the modern ones that's super strong.
The 2-stage ones are so strong, that after you use them initialy, the second stage is a "de-activator" (not the correct term) to stop the strong solvent reactions going on inside the engine.
Did one of those on my Bronco back in the early '80's and that darn stock radiator looked brand new inside until I removed it many years and miles later.
I'm sure they have improved methods today, but boy howdy did that flush work!

Where is the A/C bracket you're talking about? Was it on the passenger side, or driver's side? If passenger and part of the alternator bracket, perhaps there was a Thermactor (air pump) on your rig at some point.

Paul
1755429367424.png

1755429416920.png

1755429502175.png
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
Seen it many times in years passed, but luckily never on one of my own rigs. Usually just there at the openings, luckily too.
Since you've gone this far, I would actually flush it with one of the super-strong 2-stage cleaners. Or at least one of the modern ones that's super strong.
The 2-stage ones are so strong, that after you use them initialy, the second stage is a "de-activator" (not the correct term) to stop the strong solvent reactions going on inside the engine.
Did one of those on my Bronco back in the early '80's and that darn stock radiator looked brand new inside until I removed it many years and miles later.
I'm sure they have improved methods today, but boy howdy did that flush work!

Where is the A/C bracket you're talking about? Was it on the passenger side, or driver's side? If passenger and part of the alternator bracket, perhaps there was a Thermactor (air pump) on your rig at some point.

Paul

I am not having much luck finding 2-stage cleaners online.
 

El Kabong

Contributor
Driving stuff Henry built
Joined
Oct 8, 2009
Messages
1,559
Curious if that platform held something like a York style compressor that had been converted to pumping air.
x2. Looks like it might have been for a york compressor for on board air. They have mounting holes on multiple faces.
615z2hrFdfL._UF1000,1000_QL80_.jpg
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
Looks like more of a kit. It has the additional idler pulley on the drivers side and the harmonic balancer has a spare groove in front of the others that appears to line up with the idler and the forward offset of the platform. Idler bracket looks more than home-made. Curious how they tensioned the belt.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
My first thought on seeing that bracket was York compressor as well. Maybe someone was starting to create an OBA system using a dealer-installed A/C compressor bracket since there is no evidence of the EB having had A/C?

Given the age of everything my speculation about the limestone-like build-up is that it was tap water coolant allowed to sit for years. Aluminum is far more reactive than iron, so it makes some sense that it occurred there. While the rest of the coolant jacket may have junk in it, I'm suspecting that it is nowhere near as bad as those two spots.
Would not surprise me if the EPA kilt off any of the super aggressive coolant system flushes. I've used one of the popular rust removing agents in desperation, but that is off-label use and I'm not sure that it's all that good for the rest of the coolant system components.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
For a simple rust conversion, you could use the EVAP-o-Rust solution. I forget what it’s called (Thermo-Cure maybe?) and at least clean the rust and flush it out.
But that wouldn’t clean out the scale and goop buildup.
You could do a standard radiator flush first, then do an Evapo-Rust follow up and probably have a pretty clean system for the rest of the vehicle’s life.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
Well I went to put the new water pump on today. The PO had stripped the threads on the three top bolts. So they need a nut on the backside of them.
 
Last edited:

LUBr LuvR

Contributor
Bronco Guru
Joined
Dec 31, 2015
Messages
2,228
For a simple rust conversion, you could use the EVAP-o-Rust solution. I forget what it’s called (Thermo-Cure maybe?) and at least clean the rust and flush it out.
But that wouldn’t clean out the scale and goop buildup.
You could do a standard radiator flush first, then do an Evapo-Rust follow up and probably have a pretty clean system for the rest of the vehicle’s life.
Thermo Cure is correct, Paul. I used it on a rig that the radiator wouldn’t even drip when the petcock was removed. Wasn’t quite as stopped up as jba6555’s, but it did a good job of cleaning out the system.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
I had a bit of time this evening and I was able to use it to get everything put back together. I did not put the thermostat back in. I was concerned about chunks of debris lodging in it. Once I got it all back together, I fired Ol Rusty up and let him idle for 15 minutes. I just put straight water in this time. It went from clean clear water, to looking like a Kansas river in about 30 seconds.

1755830580019.png


I will drain it tomorrow and try it again.
 
Top