Search results

Curious if anyone has mounted this kit or something similar? I mounted my new rear bumper with swing out and lost the use of my rear view mirror. Running truck mirror on the doors, but don't like the limited view especially when backing. I think I'm spoiled with the newer vehicles...

Six months ago or so, I was rear ended in the Bronco. F150 hit me on a sweeping right turn. Fortunately we were slow rolling the turn waiting for traffic to clear so we could merge. Anyway the 35” spare took most of the impact, driving into the newish repop tailgate, bending the tire mount...

Gents Hoping everyone had a great Thanksgiving. Question regarding the programming on the Quik 4. I seem to have the shifts and downshifts close to where I want them. The shifting first through third is fantastic, it’s the third to fourth that could use some work. The shift is harsh and feels...

Specs first. 93 Mustang A9L, Ron Francis harness, 98 Explorer 5.0, 4r with UsShift. Been running fantastic for 8-9 months, put some miles on it. Yesterday sitting at a red light, the engine was idling fine, then it stumbled and starting running rough. I could accelerate from the light, but...

I have five tires and wheels off my Bronco, 15x10 Centerline Cobras withe old BFG Mud terrains. The wheels are in great shape, just need a pro polish. The tires are 20 years old, always garaged, no cracking or sun damage. These have only 1500 miles on them. They would be great off road only...

I have a new Dennis Carpenter window shield frame that I’m not going to use. It’s been sitting in my garage collecting dust and a small area of surface rust from a hand print. Other than that it’s new. Im not looking to ship, it’s too large.

Wanted to know everyone thoughts on using structural adhesive for the door post and rocker? I’m planning on using 3M 07333 on the majority of the post, minus a few areas for spot welds. The rocker would be adhesive top and bottom with spot welds on the two ends.

I thought I would post this up here first. Grabbed this from a pre-cast yard we were demobbing following a project. It’s one heck of a shear/punch but way too much for a garage. Now it’s not perfect. It’s going to need a hydraulic flush and new hoses at a min, but it does run. Comes with...

Alright heading down the dreaded no start path. Specs; 5.0 Explorer with A9L/Ron Francis. 4r70w with Us Shift. Been running great. Left the Acc key on all night. Battery was dead, now charged. Cycle the key on brake light comes on, fuel pump cycles then nothing. No click just quiet. Thoughts...

Question for the Texans. I went to register my Bronco after living here 8 years, Bronco has been non-op. I purchased this Bronco in Colorado in 2004 and changed title to my name. Moved to Washington State in 2012 and registered/changed the title to WA. Moved to TX in 15 and decided to finish...

I believe I’m receiving a Dakota VHX gauge from my wife for Christmas. Ive been reading up on the install and understand that they want you to use their sensors for water temp, and oil pressure. How does this work with the Mustang EFI? Will I need to run two sets of each sensor? I see they...

Alright, checked the search and once again this seems to be a ”me” problem. US Shift Quick 4. Verified the wiring is correct, start circuit from the starter relay, one from the key, 12v in run and I spliced the two bulk/red backup lamps to the white bkup lamp wire coming from the quick 4. The...

Ok, fresh rebuild. I have forward gears, but no reverse. US Shift trans controller. Fluid level is approx lower third of stick when cold. I haven’t checked line pressure yet, probably this weekend. Looking for ideas that will keep me from dropping the tranny again.

Installed a GM unit in tank, seems to work well. Going from external pump. What I’ve noticed with this new pump, once the engine is turned off, the pressure will drop from mid 40 psi to 20almost immediately. Over the coarse of the next hour, it will drop to zero. No problem with restarting the...

Looking for window frames. I don’t really want aftermarket unless there isn’t an option. Must be in good serviceable condition (little to no rust) and straight.

RJM /RF FI harness has #25 blue wire in the driver side loom next to the oil pressure wiring. My understanding is this is power for the air compressor. The new VA wiring has a blue wire that is connected to the binary safety switch then to the compressor. once again, this is power for the...

Wrapping up my BC AC installation and I misplaced the bolts for the compressor to Explorer serp. I thought they were M8x1.25 but no go. Anyone have the lengths and size/pitch?

I'm looking for install pics for for the new BC system, specifically where the drier is mounted and the install of the high pressure lines from the condenser and to the evaporator. I read Lars' post and that was a help for the condenser. If anyone is wondering, I did receive installation...

I've searched, but couldn't find the answer. I'm looking for a combination of standard and I believe metric sizes. The first bolts are through the 76-77angled brake bracket through the fire wall. I believe these bolts go through the pedal bracket as well? The other bolts are for the...

Title says it all. Thought I’d reach out before I bought a new one.