Search results

Hi all, finally getting close to getting the barn queen driving again. My winter project, Currently, very nice NV4500 behind a 347 SBF out of an explorer. Carbed. Stock D44, 1.5 SL, 2 inch BL. Explorer serp and stock radiator which has tranny cooling ports. Been reading a lot in the tech...

Like it says, I passed a green new paint no side window EB under tow Wassila to Anc, wondering who? I was the guy driving the Class c for the last 13 days getting here.

Just looking at new to me WH adjustable track bar, seems the bolt holes are not stock. The frame side track bar size is 3/4, and my stock frame side shows about 1/2 maybe 5/8ths? The axle side track bar uses 1 inch bolt and my oem size, verified with another makers bolt, is 3/4. What am I...

Been gone a few years for work, now mostly back :) I hope. Thinking of going back to stock height (have 3.5 lift now with shock hoops, raised track bar), and leave the 2BL due to motor and tranny (NV4500). I know one issue will be engine oil pan, I think. Yeah I have the milodon 2 sump 7...

Bronco has been in the garage for 4 months while I tried to get some time to diagnose a leak after making the move from Snottsdale to just outside Payson. I had about 1 foot circle on a floor drain pan after my drive up here, when I had zero leaks after 400 plus miles around the 101/202., some...

I searched, cannot find that answer. what the heck, my search skills are horrible. I have 35'S, 3.5sl, 2 inch bl. cut fenders. Thinking out loud, I will never need that amount of lift, built this way because it was going to crawl, that never did nor will happen now. Hate to say it, it's...

I ask because this is my Ram which has about 4 feet on it, and two feet of powder in front of it, I have chains on just have not tried moving it. Bronco is in garage, and remembered hearing folks snow bopping, just wondering how deep you run in with 35's BFG KM3 no chains? That little red spec...

Edit: fixed see last post My clutch pedal is stock bronco, same for clutch bracket mounted on frame to redirect arm. Clutch arm to clutch fork and fork stock. I have an NV 4500 with dual clutch I think it's the big orange one. Use the throwout bearing for the clutch.nv4500, I'm trying to...

Not the battery, 13.7 volts, not the wires, cause it worked fine 2 times. Didn't burn it up on first two because motor started in about 1 second each time. Pulled starter, set it on ground, hooked up charger and hit it with 40 amps, starter gear pawl pops out, no turning. I need your opinion...

OK, another in the punch list of post startup issues. Dakota digital VHX works in ACC, ON, Start, but when engine is started and running, whole instrument goes dark/off. Only thing not yet programmed is speedo, it needs to be driven to set. Dakota says I have a power issue. 13 volts and...

12 years from start of rebuild, motor starts up in 1 second of cranking, whew! Now my problem, the power steering pump pulley, the serp belt jumped back a tooth, and seems to get worse with the back end bent 90's which means new belt is needed. So no more running motor. I have the explorer...

Two gauge clusters one with original parts, one with voltage gauge used in place of ammeter. First pic below is face of one with voltage meter, second is unfortunately the back of the OEM ammeter one. Third is back of first photo with voltage meter, last is rebuilt OEM one and back then is...

Selling various autometer gauges All basically new in box, yes they have been opened and fondled. SOLD>>>>>>>>>>>>>>>>>WH stock looking 1 digit tachometer and steering wheel mount kit $50 Autometer: water temp gage 3337 analog needle Oil pressure 3327 analog needle...

I have the WH MOAB brakes using vacuum booster and wilwood MC. Bench bled the master cylinder in the truck, nose up, level master cylinder. Directions say you can do it in the truck. So I gave it a shot. 2 pumps, is all it needed to get all the air out. Or did it. I'm skeptical as all get...

Installing latch rods onto the cam which is on the handle to open the rear lifgate. The only replacement I could find are WH, these: They do sell just the yellow clips But, they do not work on OEM cam, they do fit in, they do attach to rod, but the plastic binds on the rod, and hits the...

I'm going to need a fourth, in as many years, and this thing has never been run. First two defective electrically. This one has started refusing to return to run/on after a start attempt, ie the starter will stay on, not good. What brand/provider you all using with good success? And yes...

FIXED, there is a four hole backing plate inside the hardtop for mounting the hatch hing nuts and bolts. see last post. Latest hardtop issue, getting hatch hinge nuts to not pull through. On my 73, the hardtop has 4 ovals per side to accept the 8 total screws and kep nuts, to mount the...

I bought the nice cardboard headliner from WH, but note it uses screws on sides into hard top. My 73 only screwed into roof at center and rested on the edges. Was there a difference between pre70's headliner mounting and post 70-71? In fact the front of the body/interior book is the headliner...

New never used or installed WH Family roll cage top bikini top white vinyl Bikini top but for family style roll cage, complete with windshield riser. Includes shipping to conus. Well, riser was test fit but removed, never saw light of day. sold thanks

In the final stages of bolting up dash and I find my wiper switch, which is technically new, is erratic, the plastic back is lose on the pot metal base, resulting in loss of contact and erratic wiper movement. If I hold the back tight, wipers work fine. So I get another and figure I'm going...