Search results

my cowel has rusted thru at the base of the windshield in the corners on both sides....drivers side worst....i took the fenders off to get a better look...i think the door posts are ok...looking at the base of the cowel rust is pushing out all along the top seam below the windshield....my...

you might try coker tire??? they had redlines for a chevy i restored a few years back....Paleo

i have talked to a friend of mine who works at a small aircraft build shop.....he came up with a good idea for the headliner replacement.....they use this stuff when they fab up interior of planes....it is rigid insulation sandwinched between balsa wood with a thick foil over...

i think your clutches are gone.....you could try as a quick fix is to drop the pan.....inspect.....replace fluid with Lucas trans fluid....i did this on a jeep on once it lasted another 8K miles or so before the tranny went>>>>Paleo

my hard top is driving me crazzzzzy....going down the road poping and oil canning....it has had the factory top liner removed....and over the years the ribs are out of whack....there is approx 1 inch gap between the top and the ribs.....could i weld them back to the top....how were they...

why dont you get your ham/amateur radio license.....technican class....you can go on line to AARL....free study guide....a lot of pepole i offroad with are going this way.....it will give you acess to the repeater network....Paleo KE5SSU 146.970 146.730 444.700+88.5 Osage County...

Eastwood sells several types of seam seal....brushable....calk tube....get their catalog...do some research....3M also makes some....i have used the easwood brushable and have had good results...on driprails and floor pannels....Paleo

THANKS you guys.....this is just what i need to hear/find.....i am now looking at the miller line up....i have a old lincoln cracker box....time to get updated....thanks again.....Paleo

what type of tire you running????try airing down just a little.....short term fix

i am in the process of buying a new SMALL mig welder....i have been looking at lincoln machines....any body have any thoughts.....my budjet is around $400 to 700 dollars??....would like to get the most bang for the buck????paleo

they were working on his( sams memmelo's) hot rod doin metal fab on front end then they switched to last years turkey run in fla....thats when they showed the bronco...it was one of sams buddies....had it loaded up on a motor home....they were there for the turkey run also.....didnot have any...

do you still have the smog tube????take one of the tube head plugs to the hardware store and buy pipe plugs in that size in brass to go in the head....this has worked for me in the past....i believe they were 1/4NPT male.....the brass looks ok....and easy to remove if you/someone wants to put...

paleo man here.....northen okie.....out in the osage on the arkansas river....east of ponca city, okla....77 bronco in need of floor pans...tlc...money!

i am in the same boat....wondering what to do/order...looking for some expert advise from the folks that have done it already...i was at first looking at LMC truck parts...but now i am not sure???...i have herd that some of this stuff is made overseas???...i would like good ole american know how...

dont have any pics....but when i was in creede colo one summer(back in 74 or 75) i saw a fire dept bronco that was set up way cool...it had winches front and rear....the front bumper had a platform on it where you could stand? dont know what it was used for...had a trailer that looked like a old...

is the dist. vacum advanced??...are the springs/weights working??....check fuel pump/filter??....check fireing order....when setting timming did you pull vacum line off dist. to set? or did you set with vacum line connected?...carb float set to low? starving engine?......paleo man

when you put your ammeter in the circuit....it must be in series....what you can do is get a ammeter and some jumper leads....put the meter in series with the ground to the battery....and start pulling fuses....hope this helps

ok guys...i am a nube to this form....i am starting a ground up resto on a 77 EB...i have been looking at LMC bronco truck parts....how good is the sheetmetal parts they are offering....should i look elsewhere???...my bronco needs new floor pans..TOAST....any advise would be helpful...i...

i have been reading the posts/threads on the rear quarter pannels on how they joined at the top....my question is my bunco has a hairline of rust showing in this aera....what should i do...blast it out/seam seal....drillout spots and re work on inside/outside body pannel?.....i know looks can be...

qrz.com....study guide on line KE5SSU QTH: Osage County Okla Yaseu 7800 Mobile Bronco 146.970 146.730 444.700=88.5