1973 Bronco with modified half cab. Half cab is a stock steel unit, but the rear has been modified with a sliding rear window - I believe this is from a Ranger. Bulkhead is custom as well. Instead of angling in toward the floor like a stock bulkhead, this one goes straight down leaving about 18" of storage room behind the seats. Convenient for small bags or speakers.
Bronco is cut and lifted and has been taken off road extensively over it's life. Several body panels have been dented, fixed, and then dented again.
Typical Bronco rust - front floor pans need to be replaced.
both fender aprons at the fire wall, bottom of tailgate, and the body seam on the passenger side all have rust issues.
Strong running 302 with edelbrock performer intake, carb, and air cleaner - choke housing on carb needs to be replaced. Stock three speed with a Hurst floor shift conversion. Stock Dana 20. Front Dana 44 with the knuckles out Ford disc brake conversion. Small bearing rear end, drum brakes, 28 spline axles. 3.50 gears with open differentials front and rear. Rear has had new bearings, seals, and shims within the last 500 miles.
F100 power steering conversion with Saginaw pump.
Flowkooler water pump
Bronco starts, runs, drives, and stops fine. I have driven this Bronco to Los Angeles and back (700 miles round trip) without issue. Could probably use a new battery soon.
Three gas tanks - stock main tank with metal auxiliary tanks on either side. Side tanks cannot currently be used because of a broken switching valve.
Rear traction bars.
Bronco has been completely re-wired. New fuse panel is located inside the groovy wooden dash overlay.
High back seats from a Bronco II - driver seat has a wear hole in the side.
BC Broncos two into one exhaust system (run off of stock exhaust manifolds)
ISSUES:
Rust and dent issues noted above
Gas tank issue noted above
Carb choke housing noted above
Hole in driver seat noted above
Speaker cut outs in door panels, but no speakers
The front yoke on the transfer case is incorrect, so the front driveshaft is not installed.
Carpeting has obviously been patched
No horn - no button on steering wheel and no horn in engine bay
$7,500 obo. Located in Stockton CA. Come take a look and drive it home. Runs very well.
If an out of state buyer comes along, you will need to make all shipping arrangement. I will be here to meet the shipping company, but you will need to coordinate shipper's pickup around my work schedule.
Bronco is cut and lifted and has been taken off road extensively over it's life. Several body panels have been dented, fixed, and then dented again.
Typical Bronco rust - front floor pans need to be replaced.
both fender aprons at the fire wall, bottom of tailgate, and the body seam on the passenger side all have rust issues.
Strong running 302 with edelbrock performer intake, carb, and air cleaner - choke housing on carb needs to be replaced. Stock three speed with a Hurst floor shift conversion. Stock Dana 20. Front Dana 44 with the knuckles out Ford disc brake conversion. Small bearing rear end, drum brakes, 28 spline axles. 3.50 gears with open differentials front and rear. Rear has had new bearings, seals, and shims within the last 500 miles.
F100 power steering conversion with Saginaw pump.
Flowkooler water pump
Bronco starts, runs, drives, and stops fine. I have driven this Bronco to Los Angeles and back (700 miles round trip) without issue. Could probably use a new battery soon.
Three gas tanks - stock main tank with metal auxiliary tanks on either side. Side tanks cannot currently be used because of a broken switching valve.
Rear traction bars.
Bronco has been completely re-wired. New fuse panel is located inside the groovy wooden dash overlay.
High back seats from a Bronco II - driver seat has a wear hole in the side.
BC Broncos two into one exhaust system (run off of stock exhaust manifolds)
ISSUES:
Rust and dent issues noted above
Gas tank issue noted above
Carb choke housing noted above
Hole in driver seat noted above
Speaker cut outs in door panels, but no speakers
The front yoke on the transfer case is incorrect, so the front driveshaft is not installed.
Carpeting has obviously been patched
No horn - no button on steering wheel and no horn in engine bay
$7,500 obo. Located in Stockton CA. Come take a look and drive it home. Runs very well.
If an out of state buyer comes along, you will need to make all shipping arrangement. I will be here to meet the shipping company, but you will need to coordinate shipper's pickup around my work schedule.
Attachments
-
01.jpg117.3 KB · Views: 689 -
02.jpg109.5 KB · Views: 578 -
03.jpg98.1 KB · Views: 641 -
07.jpg94 KB · Views: 658 -
12.jpg95.1 KB · Views: 593 -
14.jpg119.3 KB · Views: 574 -
27.jpg104.9 KB · Views: 667 -
26.jpg106.3 KB · Views: 573 -
21.jpg62.9 KB · Views: 454 -
06.jpg85.9 KB · Views: 486 -
13.jpg99.2 KB · Views: 446 -
10.jpg98.6 KB · Views: 424











