• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

4bbl Intake on Stock Height EB

dsenatore

Contributor
Jr. Member
Joined
Aug 21, 2002
Messages
94
Loc.
East Walpole
Good Morning,
I have an unlifted 76 w/C4 auto trans and looking to put a Holley 4548 4bbl on a 92 Lincoln 5.0 HO motor that I have waiting in the wings. Does anyone know what intakes will fit under the hood? There's a local EB'er w/a Edelbrock Torker II (Model 5021) but we're unsure if it will clear. I'm trying to keep it simple and stay non-EFI.
Thanks,
David
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
I have a cast iron intake from a '60's vintage car that is very low. I believe there were some early Mustang 5.0's with aluminum 4's I was looking at on eBay. Not sure about aftermarket.
 

56f100bbw

Contributor
Bronco Guru
Joined
Feb 3, 2008
Messages
2,406
Loc.
Tucson / lakeside AZ
On my 77 and 76 both 302’s Edelbrock aluminum intake of performer with a Edelbrock 500 carburetor with the original air cleaner fit fine I did have a chrome 14 inch air cleaner with a big drop base and it was close to the hood
 

Attachments

  • DD5D27F1-2DFC-478B-A08F-902A8CB54B93.jpeg
    DD5D27F1-2DFC-478B-A08F-902A8CB54B93.jpeg
    164.9 KB · Views: 151
  • 97D20771-6577-4D29-9A09-7594021F9DFA.jpeg
    97D20771-6577-4D29-9A09-7594021F9DFA.jpeg
    183 KB · Views: 184

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Edelbrock Performer (can’t say about the RPM model), old Holley Street Dominator, Weiand Stealth, should all fit with no body lift.
Check your mounts to make sure they’re not crushing. They should be three-quarters of an inch tall. Any less and things start to get closer and closer.

Plenty of members here using the Edelbrock performer RPM, but I don’t remember if any of them are running stock body mounts.
It’s only slightly taller than the regular model, but with so little room to work with, that slight amount could put the top of the air cleaner into the hood.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
Don't don't most combos fit with the 302? It's when you upgrade to a 351w manifolds and air cleaners matter to fit under a stock hood.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
I used an Edelbrock Performer, Holley 600 Ford style kick down carb and Hi-Po 289 air filter assembly on my all stock 68. Fit fine, looked cool.
 
OP
OP
D

dsenatore

Contributor
Jr. Member
Joined
Aug 21, 2002
Messages
94
Loc.
East Walpole
Thanks for all of the replies, it's a big help! One more question - I have the stock Motorcraft 2bbl carb w/EGR. I assume I need to find an EGR for the 4bbl, correct? Or do I now have to deal w/EGR?
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
If you’re keeping the EGR Edelbrock makes a four barrel spacer with EGR flange. Problem is it adds another inch or so to the height. So just something else to watch out for.
 
OP
OP
D

dsenatore

Contributor
Jr. Member
Joined
Aug 21, 2002
Messages
94
Loc.
East Walpole
If you’re keeping the EGR Edelbrock makes a four barrel spacer with EGR flange. Problem is it adds another inch or so to the height. So just something else to watch out for.
Thanks for the info Paul, I'll probably delete the EGR.
 
Top