• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Differential Breather Bolt

Bronco Maniac

Sr. Member
Joined
Nov 14, 2010
Messages
421
I received my new Differential Breather Bolt. Started screwing it into differential and thought it was stripped. It is too small for the hole in the differential. The hole is slightly larger than the vent threads. Not like you could get a bushing. Any thoughts?

If I could get one thing with this Bronco to go right.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
The breather bolt should be 7/16-20.

I'm relocating mine on my current rear axle build, so I just welded in the hole and drilled & tapped it in the new location, but you could do the same in the stock location. Weld it up and then drill & tap to match the breather...you may need to bush the brake line if you want a snug fit there.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
I guess it would help to ask if this is for the front or rear...I was talking about the rear breather. Clearly welding up the cast iron center section of the D44 is a bit more of a project.
 

dave67fd

Bronco Guru
Joined
Sep 24, 2010
Messages
2,864
They both use the 7/16-20 breather. I just bought both from JBG with different p/n's but their identical.
 
OP
OP
Bronco Maniac

Bronco Maniac

Sr. Member
Joined
Nov 14, 2010
Messages
421
This is the rear. The front already had a breather bolt in it. I put some hose on it the other day.

I am thinking I will drill and tap a small piece of plate for the breather bolt and weld it over the hole.

Thanks for the info. I guess it is good to know it is not just me. Everything I have touched on this thing had been like this. I guess my last Bronco build went pretty smooth.
 
OP
OP
Bronco Maniac

Bronco Maniac

Sr. Member
Joined
Nov 14, 2010
Messages
421
I was thinking about this procedure to avoid the metal shavings. Your thoughts? Thanks.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
I was thinking about this procedure to avoid the metal shavings. Your thoughts? Thanks.

I would just pull the axles and center section so that you can properly clean everything out. A magnet inside the housing is never a bad thing either, as it will catch whatever you may miss in the long run.
 

duffymahoney

Contributor
Bronco Guru
Joined
Apr 26, 2015
Messages
2,734
Breather bolt? You guys aren't running a hose barb to a hose up to the frame? A one way valve would be slick!
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Breather bolt? You guys aren't running a hose barb to a hose up to the frame? A one way valve would be slick!

I would think that you would want your breather to allow air to escape and return with thermal cycling, so wouldn't a one way valve cause you to either build pressure or vacuum in the diff, depending on which way you installed it? There are roll-over valves for fuel tank vents (and fuel cells on racing applications), so I assume you could use those or something similar on your diff/trans/tcase vents as well...has anybody?
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
There is or at least was a K&N filter made for use with long hoses from the breather bolts, to keep water from entering during water crossings.
I have seen them with 4 hose fittings, to allow front diff., rear diff., transfer case and transmission to all vent to the same filter.
 
Top