• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Door Hinge Pillar Replacment

Pipehitter

Full Member
Joined
Jan 18, 2010
Messages
152
Loc.
Clintonville WI
Newbie here, searched the tech articles and the posts, cant seem to find any detailed descriptions on the replacement of the DS and PS door post replacment. I have removed the floors in my '75 and the PS post along with the inner kick panel. Just looking for some tips on installing new post. I plan on fitting the door prior to final welding. Good news is my rockers are fine and they are still attached. Any help and pictures are appreciated - someone that went thru this already. If there is a topic on this that I missed I apologize. Thanks!
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
There are lots of posts on it. The master list of build threads has a few.

Did you measure your old post before pulling it?
You will need this to get the new one close to where it neeeds to be.
I prefer to tack weld the post, hang the door, then check for door gaps and fitment. Once in the right spot, weld in.
It took me weeks to weld mine in because I was not happy.

Some people use sheet metal screws but if you have to move the pillar you need to drill new holes. After a couple moves you will have holes all over the place and the screws dont hold like a tack weld.

Good luck and take your time. The pillar is everything to align the door and fenders.
 
OP
OP
Pipehitter

Pipehitter

Full Member
Joined
Jan 18, 2010
Messages
152
Loc.
Clintonville WI
Door Pillar

Thanks JohnJohn. Yep, I measured the old one prior to removing. Purchased a new one from Bronco Graveyard. I had to remove all of the inner kick plate that helps align the new pillar, but I guess the best is to tack in place and check the door fit up. After the fronts are welded in place I am going to tackle the rear door posts.
 

borg

Jr. Member
Joined
Feb 22, 2007
Messages
93
When I did mine, I cut the old posts off just above the bracketry that supports the upper hinge and matched the new post to the old. This worked OK. If I were going to do it again I'd probably try hanging the new post on the door (more or less centered in the adjustment) set my gaps and tack the post in place. An extra set of hands would be handy, but then that's what friends are for, right?

Steve
 
OP
OP
Pipehitter

Pipehitter

Full Member
Joined
Jan 18, 2010
Messages
152
Loc.
Clintonville WI
Borg,
Thanks for the reply. Mine were to far gone to try and save any of them, so I guess I will take it little by little. I searched the build sites per JohnJohn's reply and there are a lot of good pics and advice here. The one thing I didnt think of is the front to back angle and to be sure they are square to door. I think I will gut the doors prior to hanging for fitup, as I am sure they will be on and off quite a bit before its right!
 

Galt72

Contributor
Sr. Member
Joined
Apr 21, 2004
Messages
646
I'm just finishing up mine. I read all the posts about taking measurements and I did so on mine before removing the passenger side. I found trying to use those measurements was difficult. I got it where i thought it needed to be, sheet metal screwed it in and hung the door. The sucker was way off.

I took the door off and by chance I hung the front fender back on the bronco and noticed the fender didn't line up with the stock mounting holes and old paint markings. So I moved "beat" the pillar around until the front fender fit perfectly to the holes on both the pillar and the inner fender well. If you use the front of the fender and the rear top bolt hole and the 3 bolt holes going down the pillar as a guide it's perfectly square. I mounted the door and adjusted it in a few minutes. I moved over to the drivers side and didn't even bother with the measurements. Cut that sucker out, shoved the new pillar in, mounted the fender and squared it all up and done.
 
Top