• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

F 150 outer axle question

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,362
Guys, I have a set of outer 150s. All i want to do is go to the bigger u-joint (as inexpensive as possible). Here are my questions:
Do I use the bolt in the end of the axle or can I use the snap ring on the end of the axle if i have it machined (i can get machine work done for free)?
Can I buy the inner early bronco axles with matching u-joints and mate the two axles (150 outers and eb inners) together?

thanks
 

gravy

Bronco Guru
Joined
Sep 4, 2006
Messages
1,236
Loc.
Parsippany
axles

You canuse the outers but not the inners (all the same except for joint size on fords). You can give the driver axle a shot but it is .4 inches longer and I am pretty sure it will be to long, the pass side is 6 in to long. I just finish shortening a 78 f150 housing- I used the stock 760 outers from the 78 axle and the driver inner and got a 760 early bronco axle for JBG- I got everything from Jeffs. It worked out perfect. Let me know if you need any other info.
 
OP
OP
fordguy

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,362
gravy i dont have the inners, just the outers. I will look at the inners at JBG. I have a chevy brake kit so I guess I will see how the outers work with it (whether i use the clip or the bolt). All I want to do is move to the bigger 760 ujoint. I dont do rocks and will not do too much mud. Thanks for the info.
 

Kenny

Full Member
Joined
Jul 26, 2002
Messages
301
Since you have the Chevy disc conversion, I assume you're currently using a bolt and washer rather than the snap ring on your stock EB outers. I believe that EB outers are the same length as F150 outers (9 23/32") so you'd probably use a bolt and washer as well (assuming the snap ring groove on the F150 is on the same place as EB outer).

If you were to machine those F150 outers for a snap ring groove, my guess is that you'd want to machine the groove approx .21875 inch past the stock groove. I'm basing this number on the difference in length of F150 outers (9.71875) vs. Chevy outers (9.9375). Since I'm basing all of this on theory, it's probably a good idea to compare your stock EB outers to the F150 outers to be certain though.

Also, check out this axle link regarding a cheap swap for 297/760x axles in EB's. It focuses on axles from a mid-70's blazer or 1/2 ton 4X4, but it's very informative and has some info that can apply to you. I did this conversion for cheap, and it allowed me to use the snap ring with my Chevy discs.
 
OP
OP
fordguy

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,362
kenny i have the chevy conversion but it is not installed. i am upgrading with new gears, axles, tru trak and 4.11s. I will check out the link. What points are used to measure the outer axle.
 

Kenny

Full Member
Joined
Jul 26, 2002
Messages
301
kenny i have the chevy conversion but it is not installed. i am upgrading with new gears, axles, tru trak and 4.11s. I will check out the link. What points are used to measure the outer axle.

The measurement is from the center of the yoke to the end of the axle. Here's a link with a chart with some good D44 axle length info.
 
OP
OP
fordguy

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,362
kenny called daves evidently they have sold all the chevy axles that toddz mentioned in his write up. wish i could find a chevy dana 44 donor
 

mr.n

Sr. Member
Joined
Nov 6, 2004
Messages
710
Top