• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Holley carb issue

ep67bro

Contributor
Bronco Junky
Joined
Aug 28, 2008
Messages
3,873
Loc.
Easton, MD
I have a built 289 with a Holley truck avenger carb. the carb has been on this engine for years and never really gave me any trouble. I was planning on going wheeling this weekend and I took it for a ride. It seemed to run ok at first but when I really go on the gas hard it seemed to fall on its ass and back fire a few times. Ran fine at about 2500 rpm. I was thinking maybe a jet is clogged since the truck has sat a lot this year. got back to my shop and had it sitting and idling it seemed to be pulsing then it just died. Sounds like it ran out of fuel but then I took the air cleaner off I could see fuel coming out of the squirters. Tried to start the truck and it seems like it was flooded. Gave it full throttle and it fired back up but smoked like it was flooded. Let it idle for a minute and got out to find there was fuel coming out of the vent tube so bad it flooded the engine again! So any ideas? Float stuck open in one of the bowls? Something else? I am not a carb guru and I have never taken apart a holey carb. I have worked on Eldebrocks but I know they are completely different. I am looking for advice as I only got 4 days until I leave to wheel for the first time in 10 years really dont want to cancel at this point!
 

EODMike

Full Member
Joined
Mar 26, 2019
Messages
180
I had a similar issue with an older Holley carb. It would flood or be a bear to start after sitting for a while (couple of days). Always seemed to drain fuel down into itself, like flooding too. I finaly got a new carb. No such issues any more. I'm also not a big carb guy as far as taking them apart, but I did try before I replaced it. Good luck.
 

MS73HD302

Jr. Member
Joined
Aug 8, 2017
Messages
128
Tap the bowls with the back of a screw driver to possibly free up whatever is stuck. Holley is easy to take a part just tighten everything up in steps. I use a nutdriver so I don't warp anything by over tightening. They sell the rebuild kits at the large auto parts stores if you tear any gaskets.
 

JKH67302

Full Member
Joined
Apr 25, 2009
Messages
189
The falling on it face and back firing under load sounds like a power valve failure. The flooding might be some gunk keeping your float from seating. To fix both you need to pull the bowl to fix. Holleys are not as simple as an Edelbrock to tear down, but I'm sure there is lots of good YouTube advice. I too had lots of carb issues when it sat for a while, all of this could just be some tiny pieces of gunk in the wrong places.

Sent from my SM-G975U using Tapatalk
 

MS73HD302

Jr. Member
Joined
Aug 8, 2017
Messages
128
I had a similar issue with an older Holley carb. It would flood or be a bear to start after sitting for a while (couple of days). Always seemed to drain fuel down into itself, like flooding too. I finaly got a new carb. No such issues any more. I'm also not a big carb guy as far as taking them apart, but I did try before I replaced it. Good luck.

Mine would flood like that when the accelerator pump ball/diaphragm let loose. Fixed that and quit the draining of fuel bowls
 
OP
OP
ep67bro

ep67bro

Contributor
Bronco Junky
Joined
Aug 28, 2008
Messages
3,873
Loc.
Easton, MD
Thanks for al the input. So I am trying to find a Truck avenger rebuild kit but that are all on back order. Both Amazon and Summit dont have them in stock or I cant get them until next week. Anyone know what standard holley the 470 truck avenger is based on? I know I need a kit with the vacuum secondary. And it seem like most of the kits dont include this. I tried tapping on the bowls and it is still spewing fuel out of the vent pipe. IS it based off the 4160 carb?
 
Last edited:

brbuilder

Full Member
Joined
Aug 19, 2007
Messages
176
I replied to you other post.

Try replacing the o-ring on the needle and seat assembly or the entire needle and seat assembly. Allstate Carburetors has the parts. After I adjusted the float level mine started leaking out the vent tube. It was leaking past the o-ring on the needle and seat assembly.

Thunderhead 289 has a video about this issue.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
It is a 4160. Holley used to have specific kits for specific carburetors. Now it seems they offer a kit for all 4160s. I would call Holley and see what they recommend.
 
OP
OP
ep67bro

ep67bro

Contributor
Bronco Junky
Joined
Aug 28, 2008
Messages
3,873
Loc.
Easton, MD
So an update on this. Turns out the 470 truck avenger is based on the 4150 carb. Thats right off the Holley Web site. I found a rebuild kit local for a 4150. Took the carb off the bronco, took the fuel bowls and meter plates off didnt find any major debris or anything in the carbs it looked really good but I cleaned the bowls and needles up real good, the banjo fitting did have some crap in it. The only issue I found was the oring on the needle and seat was degraded and brittle, so I pulled the orings off the needles in the kit and put them on my old needles. I didnt bother with taking the rest of the body apart. Just sprayed all the holes real good and slapped it all back together. Fired it up and it appears to be just fine. If anything the throttle response is better than it has been in a long time. Just a note that if you have a truck avenger and get a standard 4150 rebuild kit there are a few things that worn work. 1. the needles in a standard kit will not work but the orings on them will. 2. The power valve is completely different and wont work. I didnt get in the body so there could be a few other things. Thanks for all the input.
 
Top