• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Hydroboost/ram assist?

TOFIC

Bronco Wrencher and Fixer
Joined
Jan 6, 2004
Messages
3,740
Loc.
Redcliff Alberta
Alright - I'll drill it and put it back together.
good thats the way to do it.
There wasn't any sealant holding the unit together - do I need to use any? NOPE
The 5 bolts that held it together were super tight - is that rubber seal on the piston side of the unit the only thing that keeps the high pressure fluid inside the unit?
Yes thats it, ensure the bolts are snug though

I'm going to go to the yard when I have time a grab a few of these units - they are decently easy to pull and they are cheap.[/QUOTE]
 

malcolmzilla

Bronco Guru
Joined
Mar 18, 2003
Messages
1,522
Loc.
Calgary, AB, Canada
Subscribing.

Getting a spare stock EB PS box to send to WTO for rebuild, 2.7:1 ratio and ram assist porting. Have an used Astrovan hydroboost and reman'd Lincoln saginaw dual return pump.

Question: Run the hydro assist and see how it works, or port the Hboost in advance? (scary to me - are there DIY reman kits?)
Maybe send it all to WTO?
 

OX1

Bronco Guru
Joined
Aug 26, 2003
Messages
3,472
assemble the unit and this will handle just about anything you throw at it.
The super duper ultra magnum killer mod setup has other tricks used on it and cost a lot of money to do but you will not need that one unless you are running 44's on rockwells or similar such ilk.
TOFIC

Dredging this back up.........
What about 43's on 406's with a 3" ram?

And on another note. Can you run hydroboost off an electrical/hydraulic power pack? (which I might use if I go rear steer)
 

malcolmzilla

Bronco Guru
Joined
Mar 18, 2003
Messages
1,522
Loc.
Calgary, AB, Canada
My Lincoln Saginaw, stock Astrovan hydroboost, and ported 4 turn EB box have no issues running a 1.5"x8" PSC ram assist via -6 AN hoses, even with the front locked on pavement. 35" Xterrrains.
 

Attachments

  • photo-10.JPG
    photo-10.JPG
    112 KB · Views: 92

BUCKNBRONK

Sr. Member
Joined
Jun 30, 2011
Messages
521
Loc.
fresno
I am going hydro boost, and ram assyst. I dont have a power steering box yet, so i am buying the West coast broncos' ram assyst box. The ram assyst is hooked through the p/s box. The pump dosent have to work that hard for the hydro boost,(works hardest through box). I will use a cooler for the return line to pump, and was told to me everything will work fine, with no problems.

This is all u need , the "porting" of the hb unit is not needed. Unless u plan on big axles and 48+ " tires that need 3+" rams to turn them, this tread is a waist of time getting everyone excited about drilling out hb units.
 

Danny Cabral

New Member
Joined
Aug 17, 2009
Messages
21
Loc.
Connecticut
...the "porting" of the HB unit is not needed. Unless you plan on big axles and 48+ "tires that need 3+" rams to turn them, this thread is a waist of time getting everyone excited about drilling out HB units.
I came across this thread while doing a search and I couldn't agree more with BUCKNBRONK. The Hi-Flow modified hydroboost units that Vanco sells (for ram-assist steering compatibility) are NOT simply drilled fittings. There's custom machining of the internal hydroboost components. It's NOT necessary to drill out the line fittings and/or the hydroboost threaded ports. In fact, I sent my hydroboost unit to Vanco without the fittings and reused them when it returned. Read the link below for more detailed info:
http://www.pirate4x4.com/forum/showthread.php?t=878503 (My ram-assist steering & hydroboost brake upgrade.)
 
Top