• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Lars Bars Radius Arm dimensional Questions

ITSNOTAJEEP

New Member
Joined
Aug 24, 2004
Messages
13
Loc.
ARIZONA
So I have gathered the postings related to construction of Lars Bars I could find on the interwebs. I didn't find any details on exact lengths and bend point. I did find the picture with a tape measure in it. I also know I'll need a 9 degree bend but I'd like to have a bit more details beforehand. Maybe one of you find guys or gals have additional info you can share?
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
PM me your email address. I have a word doc that is a collection of posts and pictures from Lars, describing the construction. I've never seen more information than this. Or... it was enough for me to make my own!
 

gddyap

Bronco Guru
Joined
Mar 8, 2005
Messages
1,334
Loc.
Mtn View, CA
They are 6" longer. So the bend occurs where the stock arm would end then goes on for 6". The extended portion runs parallel to and directly under the frame. That's what the bend is for. If you didn't bend it, the extension would go past the frame towards the t-case or it would place stress on the radius arm bushings on the axle end because they would be pushing out.
Did you find the original "6 inches longer" thread on norcalbroncos.com?
 

gddyap

Bronco Guru
Joined
Mar 8, 2005
Messages
1,334
Loc.
Mtn View, CA
Ask Lars. He designed it in SolidWorks (CAD software). He can send you a .pdf. I've seen a drawing. In the norcalbroncos thread, he and I discuss the slot width on the drawing being .240" and that .375" would have been better. In the end he used .375". We used his weld fixture so it wasn't critical to have a tight fitting slot to the arm web.
 

patrickk1

Jr. Member
Joined
Mar 7, 2011
Messages
135
Loc.
Cambridge
Originally I had planned on doing Lars Bars on my Bronco. After pricing out the parts, it didn't cost much more to do a full 3link.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
A 3 link is another level of difficulty beyond extended arms in getting the geometry right if you want good street manners. I'm not convinced the small gain is worth the increased effort.
 
OP
OP
I

ITSNOTAJEEP

New Member
Joined
Aug 24, 2004
Messages
13
Loc.
ARIZONA
Ask Lars. He designed it in SolidWorks (CAD software). He can send you a .pdf. I've seen a drawing. In the norcalbroncos thread, he and I discuss the slot width on the drawing being .240" and that .375" would have been better. In the end he used .375". We used his weld fixture so it wasn't critical to have a tight fitting slot to the arm web.

I am also building a fixture to ensure the arm is planar to the radius arm end. I have the fixture nearly completed but want to verify the frame joint and the arm end are where they need to be.
 
OP
OP
I

ITSNOTAJEEP

New Member
Joined
Aug 24, 2004
Messages
13
Loc.
ARIZONA
Ask Lars. He designed it in SolidWorks (CAD software). He can send you a .pdf. I've seen a drawing. In the norcalbroncos thread, he and I discuss the slot width on the drawing being .240" and that .375" would have been better. In the end he used .375". We used his weld fixture so it wasn't critical to have a tight fitting slot to the arm web.

Is Lars a member of Classic Broncos??
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
A group of the coloradoclassicbroncos.com guys got together and built a bunch of them for their Broncos, some of them are members here too.
You need to be a member to see pictures and other attachments there.
The attachments are too big to post here.
 
Top