• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Problems persist on dash gauges...

WARDOG

Full Member
Joined
May 23, 2013
Messages
263
Loc.
Graniteville, CA
I have had gauge problems for the past year.
Sometimes they work, sometimes not. Will work for a week, a month, and then not work.
I have replaced the gauge cluster regulator 3 times all with the same problems.
I have replaced the sending units (temp and oil) 3 times thinking I had a bad part but problems still persist.
I have cleaned all contacts.
Oil pressure gauge was reading half of what the mechanical gauge says.
I use teflon tape for sealant on the oil gauge and RTV sealant on the temp sensor.

Can someone explain how the gauges work. From the sending unit to the cluster, black wires going to every gauge and what the regulator actually does?
Does the sending unit measure ohm resistance and send that to the gauge?

Just frustrated.
I have considerable electronics (subpanels, relays, switch panels) to install but I need to get rid of the bugs first.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
I have had gauge problems for the past year.
Sometimes they work, sometimes not. Will work for a week, a month, and then not work.
I have replaced the gauge cluster regulator 3 times all with the same problems.
I have replaced the sending units (temp and oil) 3 times thinking I had a bad part but problems still persist.
I have cleaned all contacts.
Oil pressure gauge was reading half of what the mechanical gauge says.
I use teflon tape for sealant on the oil gauge and RTV sealant on the temp sensor.

Can someone explain how the gauges work. From the sending unit to the cluster, black wires going to every gauge and what the regulator actually does?
Does the sending unit measure ohm resistance and send that to the gauge?

Just frustrated.
I have considerable electronics (subpanels, relays, switch panels) to install but I need to get rid of the bugs first.
The original Instrument Voltage Regulator (IVR) creates a constant RMS voltage. It actually pulses, but keeps the average voltage constant. There is a newer, solid state IVR that is a true voltage regulator, with a constant voltage output. The electrical current path is from the output of the IVR, daisy-chained to one side of each of the three gauges, then from the other side of the gauge to each respective sending unit, and finally to ground. The sending units change resistance, from ~73 ohms at 0% of scale to ~10 ohms at 100% of scale.

Personal opinion... Never use Teflon tape on anything on an automobile. Just don't...

The sending units rely on a path to ground. The Teflon tape is an insulator. I use #2 Permatex for all threaded connections and have never had a problem.

The gauges measure the current flow in the path to ground through the sending unit. The lower the resistance, the more current, the higher the gauge reads. If you disconnect the wire at the sending unit (greater than 73 ohms to ground), the gauge will indicate below the bottom of the scale. If you ground that wire directly (less than 10 ohms to ground), the gauge will read above the top of the scale.

It would help to more specifically and completely describe the problems you're having with the gauges, and if the problem is isolated to one specific gauge, or is common to all three.

If the problem is common to all three then the problem is something all three gauges have in common. Like grounding. A good ground scheme will have the negative battery cable bolted to the engine block. From the engine block there will be a ground strap or cable bolted to the body, and also one to the frame. The rear of the intake manifold to the firewall is a common point for the body ground. If your vehicle grounds are suspect, you can have the kind of intermittent problems you described.
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
What he said .
I found on my '68 that EVERYTHING has to be grounded. When I bought it the gauges didn't work . The PO never reconnected the ground strap from the firewall to the motor. And apparently the instrument cluster is grounded
in that manner.
SHX
 
OP
OP
WARDOG

WARDOG

Full Member
Joined
May 23, 2013
Messages
263
Loc.
Graniteville, CA
Personal opinion... Never use Teflon tape on anything on an automobile. Just don't...
The sending units rely on a path to ground. The Teflon tape is an insulator. I use #2 Permatex for all threaded connections and have never had a problem.
SO the sealant used on sending units needs to be conductive?
I see sealant that advertises "safe for sensors" is that what they are referring to?

It would help to more specifically and completely describe the problems you're having with the gauges, and if the problem is isolated to one specific gauge, or is common to all three.
The oil pressure gauge has been reading very low (compared to the mechanical under the hood) and now doesn't work at all.
The temp gauge has not been working for months, despite changing the sending unit twice. It is sealed with Permatex 2. I'll ohm out the wires to each sensor to ensure they are not shorting out.
The fuel gauge works, although it never indicates higher than 3/4 tank.
If the problem is common to all three then the problem is something all three gauges have in common. Like grounding. A good ground scheme will have the negative battery cable bolted to the engine block. From the engine block there will be a ground strap or cable bolted to the body, and also one to the frame. The rear of the intake manifold to the firewall is a common point for the body ground. If your vehicle grounds are suspect, you can have the kind of intermittent problems you described.

I'll install some new grounding straps today as suggested.

Thank you for your reply.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
SO the sealant used on sending units needs to be conductive?
I see sealant that advertises "safe for sensors" is that what they are referring to?
The sealant doesn't need to be conductive, but it shouldn't prevent the sensor from coming in contact with the engine. If you've worked much with Teflon Tape, you would know that quite often it completely covers the threads, preventing contact between the sensor and the engine/manifold/whatever. Even Teflon paste is OK.


The oil pressure gauge has been reading very low (compared to the mechanical under the hood) and now doesn't work at all.
The temp gauge has not been working for months, despite changing the sending unit twice. It is sealed with Permatex 2. I'll ohm out the wires to each sensor to ensure they are not shorting out.
The fuel gauge works, although it never indicates higher than 3/4 tank.
I'll be interested to hear back about any change in gauge operation after you change up the grounds. A lot of people think the frame doesn't need to be grounded, but the stock fuel level sending unit grounds directly to the frame.
 
Top